Installation Instructions

ManualsBrandsToro ManualsRiding ProductsFrame Repair Kit, Reelmaster 6000-D Series Tractor

W 2006 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Printed in the USA

Frame Repair Kit

Reelmaster 6000 Series Traction Unit

Part No. 110–9740

Form No. 3355–136 Rev A

Installation Instructions

Loose Parts

Note: Use this chart as a checklist to ensure that all parts have been received. Without these parts, total installation cannot be

completed.

Description

Qty.

Side plate, R.H.

Side plate, L.H.

Flangehead bolt, 3/8 x 1 inch

Flange nut, 3/8 inch

Tipper bracket support, R.H.

Tipper bracket support, L.H.

Bolt, 5/16 x 1–1/4 inch

Washer, 5/16

Locknut, 5/16

Bolt, 3/8 x 1–3/4 inch

Washer

Bolt, 5/8 x 2 inch 3

Hood latch keeper

Pop rivets

Installation Instructions

Parts Catalog

1. Position the machine on a clean, level surface, lower the

cutting units, stop the engine, engage the parking brakes

and remove the key from the ignition switch.

2. Place a drain pan under the rear lift arm hoses

connected to the frame fittings on the side of the

machine (Fig. 1).

3. Disconnect the lift arm hoses from the frame fittings

and the lift cylinder fittings from the fittings on the lift

arm (Fig. 1). Mark all the hose and fitting locations to

ensure correct re–assembly. Cap the hoses and fittings

to prevent contamination from entering the hydraulic

system.

4. Disconnect the wire harness from the lift arm.

Note: Retain all removed components and fasteners for

re–installation unless other wise instructed.

5. Remove the (4) bolts and washers securing each rear lift

arm to the frame (Fig. 1). Retain the upper rear bolt and

all of the washers. Rest the lift arm on the rear tire.

Figure 1

1. Lift arm hoses

2. Lift cylinder hoses

3. Lift arm

4. Lift cylinder

5. Tipper support bracket

6. Frame section bolts

7. Hood latch keeper

8. ROPS

6. Remove the bolts, washers and nuts securing the tipper

support brackets to the frame rail, frame rail flange and

to the motor mounts (Fig. 1). Retain the bolts, washers

and nuts that secure the front tabs of the tipper support

brackets to the engine supports. Discard all other

fasteners.

Note: When disconnecting the tipper bracket supports from

the engine mounts, it is not necessary to remove the bolts.

Only remove the nuts and washers.

7. Remove the (2) frame section bolts located rear of the

ROPS (Fig. 1).

8. Remove the hood latch keeper from each side of the

machine (Fig. 1). Make sure the rivets are removed

from the mounting holes. Discard the keepers.

9. Remove the tipper bracket and the roller assembly from

the old tipper support brackets (Fig. 2).

Summary of content (2 pages)

PAGE 1
Form No. 3355–136 Rev A Frame Repair Kit Reelmaster 6000 Series Traction Unit Part No. 110–9740 Installation Instructions Loose Parts Note: Use this chart as a checklist to ensure that all parts have been received. Without these parts, total installation cannot be completed. Description Qty. Side plate, R.H. Side plate, L.H. Flangehead bolt, 3/8 x 1 inch Flange nut, 3/8 inch 1 1 2 2 Tipper bracket support, R.H. Tipper bracket support, L.H.
PAGE 2
• Using the newly drilled holes, mount the front end of each side plate to the frame rail with (2) 1/2 x 1–3/4 inch flange head bolts. Torque to 75–85 ft–lbs 3 13. Using the fasteners previously removed, mount a tipper bracket and roller assembly to each new tipper bracket support (Fig. 2). 14. Install the tipper bracket support (Fig.