Installation Instructions

ManualsBrandsToro ManualsRiding ProductsRear View Mirrors Kit, Groundsmaster 3400 Traction Unit or CT2240, LT3340, or LT-F3000 Triple Turf Mower

FormNo.3440-138RevA

RearViewMirrorsKit

Groundsmaster

3400TractionUnitorCT2240,LT3340,or

LT-F3000TripleTurfMower

ModelNo.111-9895

InstallationInstructions

PurchasingtheDebris

Shields

MachineModels30654,30657,and

30659

Partsneededforthisprocedure:

Leftdebrisshield(soldseparately—ToroPartNo.

134-0286-03)

Rightdebrisshield(soldseparately—T oroPartNo.

134-0287-03)

Procedure

Purchasetheleftandrightdebrisshieldsfromyour

authorizedT orodistributor.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

g323795

Figure1

2.Engagetheparkingbrake.

3.Lowerthecuttingunits.

4.Shutofftheengineandremovethekey.

5.Waitforallmovingpartstostop.

6.Unlatchandraisetheoperator’splatform.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUK

AllRightsReserved

*3440-138*A

Summary of content (8 pages)

PAGE 1
Form No. 3440-138 Rev A Rear View Mirrors Kit Groundsmaster® 3400 Traction Unit or CT2240, LT3340, or LT-F3000 Triple Turf Mower Model No. 111-9895 Installation Instructions 1 2 Purchasing the Debris Shields Machine Models 30654, 30657, and 30659 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. Parts needed for this procedure: 1 Left debris shield (sold separately—Toro Part No. 134-0286-03) 1 Right debris shield (sold separately—Toro Part No.
PAGE 2
Discarding Removed Parts 3 Machine Models 30654, 30657, and 30659 Discard the flange-head capscrews, flange locknuts, and debris shield that you removed in Removing the Shields (page 2). Removing the Debris Shield No Parts Required Retaining and Discarding Removed Parts Removing the Shields Machine Models 31654, 31657, and 31659 Machine Models 30654, 30657,30659, 31654, 31657, and 31659 1. • Retain the debris shield that you removed in 3 Removing the Debris Shield (page 2).
PAGE 3
Drilling the Left Platform Support 1. Measure the platform bracket 25.5 mm (1 inch) as shown in Figure 4, and mark the bracket. g325804 g325802 Figure 5 7. Remove any burrs from the holes. Drilling the Right Platform Support 1. Measure the platform bracket 22.9 mm (29/32 inch) as shown in Figure 6, and mark the bracket. g326740 Figure 4 2. Measure the platform bracket 17.2 mm (5/8 inch) as shown in Figure 4, and mark the bracket. 3. Measure the platform bracket 84.
PAGE 4
3. Measure the platform bracket 84.3 mm (3-5/16 inch) as shown in Figure 6, and mark the bracket. 4. Measure the platform bracket 16.1 mm (5/8 inch) as shown in Figure 6, and mark the bracket. 5. Centerpunch the platform bracket at the intersecting marks. 6. Drill a 7 mm (1/4 inch hole) at each of the centerpunch marks (Figure 7). location of the countersink. Align the countersink of the mirror bracket away from the mirror-arm mount. g323913 Figure 8 g325803 Figure 7 7. 1.
PAGE 5
. Align the holes in the right mirror bracket with the holes in a mirror-arm mount (Figure 8). Note: Align the countersink of the mirror bracket away from the mirror-arm mount. 6. Repeat step 2 through 4 for the mirror bracket, mirror-arm, and mirror. 6 Assembling the Mirrors to the Machine Parts needed for this procedure: 4 Flange-head screw (6 x 25 mm) 4 Flange locknut (6 mm) Procedure g323955 Figure 10 Note: Determine the left and right sides of the machine from the normal operating position.
PAGE 6
7 8 Preparing the Debris Shields Installing the Debris Shield Machine Models 30654, 30657,30659, 31654, 31657, and 31659 Machine Models 31654, 31657, and 31659 Parts needed for this procedure: No Parts Required Procedure 1. Remove the knock-out panels from the left and right debris shields (Figure 11). 6 Flange-head screw (6 x 20 mm) 6 Flange locknut (6 mm) Procedure 1.
PAGE 7
screws (6 x 20 mm) and 3 flange locknuts (6 mm). 3. Align the holes in the right debris shield with the holes in the right platform support and the hole in the platform-pivot bracket (Figure 12). 4. Secure the debris shield to the platform support and pivot bracket with 3 flange-head screws (6 x 20 mm) and 3 flange locknuts (6 mm).
PAGE 8