Installation Instructions

ManualsBrandsToro ManualsRiding ProductsPull Link Kit for DPA Reel Mower Groomer, Greensmaster 3250-D

FormNo.3416-524RevB

PullLinkKitforDPAReelMowerGroomer

Greensmaster

3250-DSeriesTractionUnit

ModelNo.112-9248

InstallationInstructions

Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Installation

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Shutofftheengineandremovethekey.

InstallingtheFrontCarrier

Frames

Partsneededforthisprocedure:

2Rightlinkbracket

Leftlinkbracket

Carriagebolt

4Flatwasher

4Locknut

4Bushing

4Longpull-armextension

Bolt—3/8x1-1/2inches(2006andearliermachines

only)

Rollershaft(2007andaftermachinesonly)

Bolt—3/8x2inches(2007andaftermachinesonly)

Bushing(2007andaftermachinesonly)

2006andEarlierMachines

1.Slidebackthesleeveontheball-jointreceiver

andremovethereceiverfromtheballstud

(Figure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3416-524*B

Summary of content (4 pages)

PAGE 1
Form No. 3416-524 Rev B Pull Link Kit for DPA Reel Mower Groomer Greensmaster® 3250-D Series Traction Unit Model No. 112-9248 Installation Instructions Determine the left and right sides of the machine from the normal operating position. 2 Installation 1 Preparing the Machine Installing the Front Carrier Frames Parts needed for this procedure: No Parts Required Procedure 2 Right link bracket 2 Left link bracket 4 Carriage bolt 1. Park the machine on a level surface. 4 Flat washer 2.
PAGE 2
g218544 Figure 1 g218546 Figure 2 1. Roller shaft 2. Ball stud 7. Flat washer 8. Spacer 1. Roller shaft 3. Ball-joint receiver 9. Bushing 2. Ball stud 9. Spacer 10. Bushing 4. Jam nut 10. Pull-link assembly 3. Ball-joint receiver 11. Pull-link liner 5. Pull-link extension 11. Anti-scalp roller 4. Jam nut 12. Pull-link assembly 5. Long pull-link extension 13. Link bracket 6. Carriage bolt 14. Bolt (3/8 x 1-1/2 inches) 7. Locknut 15. Anti-scalp roller 6. Bolt 2.
PAGE 3
Note: Make sure the basket lips are parallel with the reel blades all the way across the reel blades. 11. Tighten the jam nuts. 2007 and Later Machines 1. Slide back the sleeve on the ball-joint receiver and remove the receiver from the ball stud (Figure 3) g218652 Figure 4 8. Flat washer 9. Bushing 1. Roller shaft 2. Ball stud 3. Ball-joint receiver 10. Spacer 4. Jam nut 11. Pull-link assembly 5. Long pull-link extension 12. Link bracket 6. Carriage bolt 13. Bolt (3/8 x 2 inches) 7.
PAGE 4
11. Note: Make sure that the basket lips are parallel with the reel blades all the way across the reel blades. clearance for 2007 and after machines, between the lip of the basket and the reel blades. Tighten the jam nuts. with the reel blades all the way across the reel blades. Note: Ensure that the basket lips are parallel 3 5. Installing the Rear Carrier Frame Parts needed for this procedure: 2 Short pull-arm extension Procedure 1.