Installation Instructions

ManualsBrandsToro ManualsAttachmentsFoot-Operator Deck Lift Kit, Groundsmaster 7200/7210 Traction Unit

FormNo.3358-656RevA

FootOperatedLiftKit

ForGroundsmaster7200/7210TractionUnit

ModelNo.112–9540

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Pedalshaft

Selftappingscrew

Mountthepedalshaftassembly

Liftlever

Levergrip1

Threadedrod1

Replacethedeckliftlever

Pedal1

Threadedrod1

Foamhose1

Hexnut(3/8inch)

Balljointend1

Linkageyoke1

Screw(3/8x1-1/4inches)

Nut(3/8inch)

Assemblethelinkage

Snapring

Clevispin

Cotterpin

Mountthelinkage

Thiskitcanonlybeusedontractionunitswithserial

numbersafter270000001.

MountthePedalShaft

Assembly

Partsneededforthisprocedure:

Pedalshaft

Selftappingscrew

Procedure

1.Locatethetwopilotholesintherightsideofthe

carrierframe(Figure1).

Figure1

1.Pilotholes

2.Drillouttheholesto5/16inchdiameter.

3.Mountthepedalshafttothesideofthecarrierframe

withtwo3/8inchselftappingscrews.Positionthe

pedalstoponthesideofthecarrierframeasshown

inFigure2

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3358-656 Rev A Foot Operated Lift Kit For Groundsmaster 7200/7210 Traction Unit Model No. 112–9540 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Pedal shaft Self tapping screw Lift lever Lever grip Threaded rod Pedal Threaded rod Foam hose Hex nut (3/8 inch) Ball joint end Linkage yoke Screw (3/8 x 1-1/4 inches) Nut (3/8 inch) Snap ring Clevis pin Cotter pin Use Qty.
PAGE 2
Replace the Deck Lift Lever Parts needed for this procedure: Figure 2 1. Pedal shaft 1 Lift lever 1 Lever grip 1 Threaded rod Procedure 2. Self tapping screws 1. Lower the mower deck completely to the ground. 2. Remove the cotter pin securing the valve link to the lift lever (Figure 4). Remove the valve link from the lift lever. Retain all fasteners for installation of the new lift lever. 4.
PAGE 3
Figure 6 1. Threaded rod 2. Foam hose 3. 10 inches 2. Thread a hex nut onto each end of the threaded rod (Figure 7). Figure 5 1. 2. 3. 4. Lift lever Washer Spacer Grip 5. 6. 7. 8. Valve link Bolt Cotter pin Flange nut 6. Connect the valve link to the lift lever with a cotter pin Figure 5. Figure 7 1. 2. 3. 4. 3 Assemble the Linkage Pedal 1 Threaded rod 1 Foam hose 2 Hex nut (3/8 inch) 1 Ball joint end 1 Linkage yoke 1 Screw (3/8 x 1-1/4 inches) 1 Nut (3/8 inch) 5. Linkage yoke 6. .
PAGE 4
Operation The deck lift pedal raises and lowers the mower deck. The engine must be running for you to use this pedal. • Press down on the front of lift pedal to raise the mower deck. • Press down on the rear of lift pedal to lower the mower deck. Important: Do not continue to hold the pedal down after the mower has fully raised or lowered. Doing so will damage the hydraulic system. Figure 8 1. Threaded rod 2. Pedal 3. Bolt 4.