Installation Instructions

ManualsBrandsToro ManualsRiding ProductsLift Arms and Shaft Kit, Groundsmaster 7200/7210 Traction Unit

Form No. 3358-247 Rev A

Lift Arms and Shaft Kit

For Groundsmaster 7200/7210 Traction Unit

Model No. 112–9545

Installation Instructions

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

Deck Lift Arm - R.H.

Deck Lift Arm - L.H.

Deck Lift Shaft

Flange Bushing

Hardened Washer

Replace the Deck Lift Arms and Lift

Shaft

Control Arms

Replace the Transmission Control

Arms

Cone Lock Nut

Replace the Motion Control Lever

Nuts

Retaining Ring

Secure the Damper

Cable Clamp

Cable Tie

Reposition the Vent Hose

Flat Washer

Flat Washer .469 x .922

Secure the Seat Belt

Cap screw (1/4 x 1–3/4 inch)

Flat washer .281 x .625

Hose clamp

Secure the Fuel Line

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Summary of content (8 pages)

PAGE 1
Lift Arms and Shaft Kit Form No. 3358-247 Rev A For Groundsmaster 7200/7210 Traction Unit Model No. 112–9545 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Qty. Use 1 Deck Lift Arm - R.H. Deck Lift Arm - L.H.
PAGE 2
Step 6. On the right side of the machine, remove the screw and pivot pin securing the hydraulic cylinder to the lift arm (Figure 2). Pivot the cylinder out of the lift arm. 1 Replace the Deck Lift Arms and Deck Lift Shaft Parts needed for this step: 1 1 1 2 2 Deck Lift Arm - R.H. Deck Lift Arm - L.H. Deck Lift Shaft Flange Bushing Hardened Washer Procedure 1. Disengage the PTO, move the motion control levers to the neutral locked position and set the parking brake. 2.
PAGE 3
Step Step 2 3 Replace the Transmission Control Arms Replace the Motion Control Lever Nuts Parts needed for this step: Parts needed for this step: 2 2 Control Arms Cone Lock Nut Procedure Procedure 1. Remove the retaining ring securing the control rod end to the transmission control arm pin (Figure 3). 1. Remove the mounting nut from each motion control lever hub (Figure 4). Discard the nut. 2. Remove the bolt securing the control arm to the transmission shaft (Figure 3).
PAGE 4
Step 4 Secure the Damper Parts needed for this step: 2 Retaining Ring Procedure Figure 6 1. Vent hose Push a retaining ring onto each damper mount pin (Figure 5). 2. Cable clamp 2. Remove the cable tie securing the top of vent hose to the frame (Figure 7). Figure 5 1. Damper 2. Retaining ring Step 5 Reposition the Vent Hose Parts needed for this step: 1 1 Figure 7 Cable Clamp Cable Tie 1. Vent hose Procedure 2. Cable tie 3. Reposition the hose away from damper as shown in Figure 6. 1.
PAGE 5
Step Step 6 7 Secure the Seat Belt Secure the Fuel Line Parts needed for this step: Parts needed for this step: 2 2 2 2 2 Flat Washer Flat Washer .469 x .922 Procedure Cap screw (1/4 x 1–3/4 inch) Flat washer .281 x .625 Hose clamp Procedure 1. Remove the cap screw and washer securing the seat belt to the side of the seat (Figure 8). 1. Remove the two nuts and cap screws securing the spacers to the seat support (Figure 9). 2. Apply Blue Loctite or equivalent to the threads of the cap screw.
PAGE 6
PAGE 7
PAGE 8