Use and Care Manual

ManualsBrandsToro ManualsOther Mower AttachmentsHourmeter Kit for TimeCutter Z

FormNo.3357-927RevB

HourMeterKit

forZero-Turn-RadiusRidingMower

ModelNo.112-9763

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Hourmeter1

Mountingclip(somekitsonly)

Assemblethehourmeter.

Selftappingscrews

2Installthehourmeter.

Hourmeterwiringharness1

Connectthehourmeter.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurfaceanddisengage

thebladecontrolswitch.

2.Movethemotioncontrolleversoutwardtothe

parkposition,stoptheengine,removethekey,and

waitforallmovingpartstostopbeforeleavingthe

operatingposition.

3.Lifttheseatforwardandlowerittotheoorboard

toaccessthebattery,frameandwiringharness.

4.Locatethebatteryandnegativeterminal.

Servicingamachinewithaliveelectricalsystem

canresultinelectricshock.

Always

disconnect

thenegative(black)battery

cablebeforeperforminganyserviceonthe

machine.

5.Disconnectthenegative(black)groundcablefrom

thebatterypost.Retainallfasteners.

Incorrectbatterycableroutingcoulddamage

themachineandcablescausingsparks.Sparks

cancausethebatterygassestoexplode,

resultinginpersonalinjury.

•Always

disconnect

thenegative(black)

batterycablebeforedisconnectingthe

positive(red)cable.

•Always

connect

thepositive(red)battery

cablebeforeconnectingthenegative(black)

cable.

AssemblingtheHourMeter

Partsneededforthisprocedure:

1Hourmeter

Mountingclip(somekitsonly)

Procedure

Locateandinspectthehourmeterinlooseparts.

PrintedintheUSA.OriginalInstructions(EN)

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3357-927 Rev B Hour Meter Kit for Zero-Turn-Radius Riding Mower Model No. 112-9763 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 2 3 4 Description Use Qty. Hour meter Mounting clip (some kits only) 1 1 Assemble the hour meter. Self tapping screws 2 Install the hour meter.
PAGE 2
• For hourmeters with a separate mounting clip: Install the hour meter to the bracket with a mounting clip as shown in Figure 1 1 2 3 1 4 2 3 G005542 G005302 Figure 1 1. Hour meter 2. Bracket Figure 3 3. Mounting clip 1. Self tapping screw 2. Hour meter • For hourmeters with integrated mounting clips: Install the hour meter to the bracket as shown in Figure 2. 3. Holes in frame 4. 2. Use the self tapping screws to install the bracket onto the seat support in the orientation shown in Figure 3.
PAGE 3
1 6 1 5 2 7 3 3 G005545 2 Figure 5 1. Ignition switch base 3. Single wire and outer terminal 2. Wiring harness 4 6. Remove the single wire from the outer terminal at the base of the ignition switch (Figure 5). G005544 Figure 4 1. Hour meter 5. Single female terminal, wiring harness 2. Female box connector 6. Enclosed male terminal, wiring harness 3. Positive male plug 7. Negative male plug, hour meter 4. Ring connector to negative 8.
PAGE 4
7. Install the single female terminal at the end of the hour meter wiring harness to the open terminal on the base of the ignition switch (Figure 6). 3 4 7 5 1 2 G005546 6 Figure 6 1. Hour meter wiring harness 5. Single wire removed previously 2. Wiring harness 6. Open terminal, ignition switch 3. Enclosed male terminal, 7. Ignition switch base wiring harness 4. Single female terminal, wiring harness 8.