Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 114-3521

FormNo.3362-528RevC

StripingKit

forGrandStand

Mowers

ModelNo.114–3521

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemower.

Hingeplate2

Bolt,(3/8x1-1/4inches)

Largelockwasher,(3/8inch)

Locknut,(3/8inch)

Washer2

Installthehingeplates.

Carriagebolt(3/8x1inch)

Locknut,(3/8inch)

Installthemountingbrackets.

Spring

Clevispin

Hairpincotterpin2

Installtherollerassemblytostriper

bracketmounts.

Nopartsrequired

–

Connectthechains.

PreparingtheMower

NoPartsRequired

Procedure

1.Thoroughlycleanmowerdeck.Alldebrismustbe

removedtoensurethekitwilltproperly.

2.Repairallbentordamagedareasandreplaceany

missingparts.

3.Raisetheplatformandverifythelatchissecurely

engagedtoholdtheplatformup.

InstallingtheHingePlates

Partsneededforthisprocedure:

2Hingeplate

Bolt,(3/8x1-1/4inches)

Largelockwasher,(3/8inch)

Locknut,(3/8inch)

2Washer

Procedure

1.Installthehingeplatetothebottomofthemower

neartherearwheelswith2bolts(3/8x1-1/4

inches),largelockwasher,(3/8inch),washerand2

locknuts(3/8inch)(Figure1).

2.Positionthehingeplatessothereartiedownsare

intheslot.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3362-528 Rev C Striping Kit for GrandStand® Mowers Model No. 114–3521 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
Note: The washer is a spacer placed inside the frame to center the bolt in the large frame hole. 1 2 3,4 2 g013800 Figure 1 1. Locknut, (3/8 inch) 2. Large lock washer, (3/8 inch) 3. Washer 4. Right side of machine 1 Figure 2 1. Use the outside holes for narrow base mowers 2. Use the inside holes for wide base mowers 5. Hinge plate 6. Bolt, (3/8 x 1-1/4 inches) 7. Slot in hinge plate 8. Rear tie down 3. 6 inches (152.4 mm) for narrow base mowers 4. 10 inches (254 mm) for wide base mowers 3.
PAGE 3
2 4 1 Installing the Roller Assembly to Striper Bracket Mounts Parts needed for this procedure: 2 Spring 2 Clevis pin 2 3 4 5 1 G010979 Figure 5 Hairpin cotter pin 1. Hairpin cotter pin 2. Left spring long finger 3. Clevis pin Procedure 1. Position the springs into the striper mounting brackets (Figure 4). Ensure the short outside finger on the spring is in the slot in the roller mount (Figure 6). 4. Right spring long finger 5. Roller assembly 4.
PAGE 4
5 Connecting the Chains No Parts Required Procedure 1. Hold the operator platform while releasing the platform latch. Lower the platform completely down. Figure 8 2. With the platform down, raise the roller up and rotate the lift handle over the platform (Figure 7). 1 1. Hole in the lower front side 3. Right snap ring with hook towards the inside of the plate of the platform machine 2. Snap ring 4. Left snap ring with hook towards the inside of the machine 2 3 G011307 Figure 7 1. Platform down 2.
PAGE 5
Operation • Stiff grass where wheel tracks are less visible will usually produce poor striping. Raising the Roller • Cool season grass types found in northern areas are usually good for striping. With the platform down, raise the roller up and rotate the lift handle over the platform (Figure 9). 1 • Warm season grass types found in southern areas will usually produce less pronounced striping.
PAGE 6
• Mowing in morning dew can produce good striping contrast. week to establish a checkerboard or a plaid style of mowing pattern. • Double cut mowing, and mowing a second pass at a 1/2 inch lower height of cut can produce good striping contrast. • Do not mow in the exact same pattern every week. This will cause compaction in wheel tracks, and may produce ruts or depressions along the wheel tracks.
PAGE 7
Notes: 7
PAGE 8