Installation Instructions

ManualsBrandsToro ManualsRiding ProductsSwitch Adapter Kit, Groundsmaster 300 Series Traction Unit

Form No. 3358-285 Rev A

Switch Adapter Kit

For Groundsmaster 300 Series Traction Unit

Model No. 114–4110

Installation Instructions

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

Switch

Adapter harness

Seat support bracket

Prop rod

Skid clip

Washer head screw

Roll pin

Install the Seat Switch

Switch

Adapter harness

Switch bracket

Screw (3/8 x 3/4 inch)

Lock washer (3/8 inch)

Switch actuator bracket

Screw (1/4 x 3/4 inch)

Nut (1/4 inch)

Install the PTO Switch

Step

Replace the Seat Switch

Parts needed for this step:

Switch

Adapter harness

Seat support bracket

Prop rod

Skid clip

Washer head screw

Roll pin

Procedure

1. P ark the mac hine on a lev el surface , lo w er

the cutting unit, stop the engine , eng ag e the

parking brak e and remo v e the k ey from the

ignition switc h.

2. Unlatc h and remo v e the instr ument co v er

( Figure 1 ).

Figure 1

1. Instrument cover

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Summary of content (8 pages)

PAGE 1
Form No. 3358-285 Rev A Switch Adapter Kit For Groundsmaster 300 Series Traction Unit Model No. 114–4110 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Step 1 2 Use Qty.
PAGE 2
3. Disconnect the negative battery cable from the battery. 4. Pivot the seat forward and secure it to prevent it from falling accidentally. Do not use the seat prop rod to secure the seat. 5. On models used internationally, remove the ﬂange screw, truss head screw, (2) locknuts and the spacer securing the sealing plate, over the fuel tank, to the frame. Remove the sealing plate. Figure 3 1. Pin 2. spring 6.
PAGE 3
14. Insert the button end of the seat switch up through the hole in the new seat switch bracket and loosely secure it to the bracket with the jam nut (Figure 4). If there is no continuity, proceed to the next step. 22. Sit on the seat. The seat switch should have continuity. If there is no continuity, recheck switch installation. If there is continuity, disconnect the continuity tester or ohm meter from the seat switch connector and proceed to the next step.
PAGE 4
Step 2 Replace the PTO Switch Parts needed for this step: 1 1 1 2 2 1 1 1 Switch Adapter harness Switch bracket Screw (3/8 x 3/4 inch) Lock washer (3/8 inch) Switch actuator bracket Screw (1/4 x 3/4 inch) Nut (1/4 inch) Figure 8 1. PTO lever 5. Remove the rubber boot and the top jam nut from the button end of the new PTO switch (Figure 9). Procedure 1. Move the PTO lever forward to the ON position. 2.
PAGE 5
moved to the OFF position. Tighten the jam nuts to 75 in-lbs. Important: The switch threads will be damaged if the jam nuts are over tightened. 10. Connect the wire harness adapter to the switch wire harness (Figure 9). 11. Reinstall the rubber boot to the top of the switch (Figure 9). 12. Connect a continuity tester or ohm meter to the switch connector. With the PTO lever in the ON position the switch circuit should not have any continuity. If there is continuity, recheck switch installation.
PAGE 6
PAGE 7
PAGE 8