Installation Instructions

ManualsBrandsToro ManualsAttachmentsWork Light Kit, Groundsmaster 360/4010/5900/5910 Traction Unit

FormNo.3393-797RevA

WorkLightKit

Groundsmaster

360/4010/5900/5910TractionUnit

ModelNo.114-5610

InstallationInstructions

Safety

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Disconnectthenegativecablefromthe

battery.

Worklight4

Washer16

Installingtheworklights.

Worklight4

Washer16

Installtheworklights.

Switch

Decal(130-5989)

Installtheswitch.

Fuse,15amp1

Installthefuse.

Nopartsrequired

–

Connectthenegativecabletothe

battery.

Nopartsrequired

–

Adjusttheworklights.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3393-797*A

Summary of content (8 pages)

PAGE 1
Form No. 3393-797 Rev A Work Light Kit Groundsmaster® 360/4010/5900/5910 Traction Unit Model No. 114-5610 Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
1 4 Disconnecting the Negative Cable from the Battery 5 6 7 No Parts Required Procedure g028310 1. Move the machine to a level surface. Figure 1 2. Stop the engine, wait for all moving parts to stop, engage the parking brake, and remove the key from the ignition. 3. Remove the rear access panel to expose the batteries. 4. Disconnect the negative battery cable from both of the batteries. 1. Roof 5. Bushing 2. Head liner 3. Nut 4. Washer 6. Small fastener 7. Washer 2.
PAGE 3
1 3 2 3 Installing the Work Lights (For 2015 and Newer Models Only) Parts needed for this procedure: g028312 Figure 3 1. Hex nut 3. Work light 4 Work light 16 Washer 2. Washer Procedure 5. Mount the work lights to the head liner using the lock washer and hex nut previously removed and additional flat washers provided in the kit (Figure 4) 1. Remove the 22 nuts and 22 washers that secure the roof to the headliner (Figure 5). 1 1 23 3 2 4 5 g028313 g028382 Figure 5 1. Cover Figure 4 1.
PAGE 4
1 4 Installing the Switch Parts needed for this procedure: 1 Switch 1 Decal (130-5989) Procedure 1. Carefully cut the decal material to expose the hole in the cab control panel (Figure 8). g028385 Figure 6 1. Work light mounting holes 3. Remove the hex nut and lock washer from each work light mounting stud (Figure 3). 4. Mount the work lights to the head liner using the lock washer and hex nut previously removed and additional flat washers provided in the kit (Figure 7).
PAGE 5
3. Install the roof to the headliner and secure with the fasteners that you previously removed. 7 5 Adjusting the Work Lights No Parts Required Installing the Fuse (For 2014 and older models only) Procedure Rotate the lights up or down and from side to side to attain the desired operating position. Parts needed for this procedure: 1 Fuse, 15 amp Procedure 1. Open the cab fuse box located on the head liner (Figure 10). g028337 Figure 10 1. Fuse 2.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8