Installation Instructions

ManualsBrandsToro ManualsWalk-Behind MowersReplacement Handle Kit, Greensmaster Flex 18 Mower

FormNo.3377-389RevA

ReplacementHandleKit

Greensmaster

Flex™18and21Mowers

ModelNo.115-1728

ModelNo.115-1729

InstallationInstructions

RefertotheToroServiceManualforadditionalinformation

ondisconnecting,connectingandadjustingthehandleand

controls.

PreparingforInstallation

IfyouareinstallingthiskitonaFlex21mowerwitha

serialnumberbetween210000001and220999999,you

mustobtainthefollowingpartsfromyourAuthorizedToro

Distributorbeforeinstallingthereplacementhandle:

Figure1

1.Bolt(1x0.25inch)

3.Throttlelever

2.Frictionwasher4.Locknut

PartNumberDescription

Qty

108-3179Throttlelever1

66-2921Frictionwasher2

33113-025

Bolt(1x0.25inch)

33113-00Locknut1

RemovetheOldHandle

1.Parkthemoweronalevelsurface.Makesurethe

engineisoff.Removethehightensionleadfromthe

sparkplug.

2.Movethethrottleandtraction/reelcontrolstothe

disengagedposition.

3.Removethe4screwssecuringthecontrolpaneltothe

handlebrackets(Figure2).Allowthecontrolpanelto

restonthecontrols.

Figure2

1.Controlpanel

2.Mountingscrews

4.Removetheboltsecuringthebrakecableendtothe

brakelever(

Figure3)Also,removethesnapring

securingthecablehousingtothecontrolbracketand

removethecablefromthebracket.

Note:Thebrakeleverandmountingfastenersmay

differduetodesignchanges.

Figure3

1.Brakecable

4.Spacer

2.Bolt5.Bolt

3.Brakelever

5.Removethescrewandlockwasher(ifapplicable)

securingthebrakelevertothebrakebracket(Figure3).

Allowthebrakelevertohangintheslotintheconsole

6.Removethescrewandwashersecuringthepinofthe

tractioncontrolrodhandletothetractioncontrol

(

Figure4).Whenremovingthescrewandwasherfrom

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3377-389*A

Summary of content (4 pages)

PAGE 1
Form No. 3377-389 Rev A Replacement Handle Kit Greensmaster® Flex™ 18 and 21 Mowers Model No. 115-1728 Model No. 115-1729 Installation Instructions Refer to the Toro Service Manual for additional information on disconnecting, connecting and adjusting the handle and controls.
PAGE 2
lever, make sure to account for the detent ball and spring which will fall out of the lever. Figure 6 Figure 4 1. Traction control lever 4. Spring 2. Screw 3. Washer 5. Detent ball 1. Traction/throttle control assembly 2. Lever pin 11. Remove the flange nuts securing the handle ends to the pivots pins (Figure 7). Remove the pivot pin spacers and discard but retain the nuts for the installation of the new handle. 7.
PAGE 3
• From the outer side of the handle, insert a flange 3. Secure the handle ends to the mower pivot pins with the flange nuts previously removed (Figure 7). head bolt through the handle bracket and clamp (Figure 9). 4. Loosely mount the top of the control bracket to the right side of the handle with a M8 x 1.25 bolt and lock nut. Position the bracket and fasteners as shown in Figure 8. • Repeat the procedure on the other side of the handle. 7.
PAGE 4