Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 115-7468

FormNo.3369-284RevA

60and72inchRecycler

Kit

ZMaster

G3andGrandStand

Mower

ModelNo.115-7468

ModelNo.115-7469

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Safety

SideDischargeorMulchGrass

WARNING

Withoutthegrassdeector,dischargecover,or

completegrasscatcherassemblymountedin

place,youandothersareexposedtobladecontact

andthrowndebris.Contactwithrotatingmower

blade(s)andthrowndebriswillcauseinjuryor

death.

•Neverremovethegrassdeectorfromthemower

becausethegrassdeectorroutesmaterialdown

towardtheturf.Ifthegrassdeectorisever

damaged,replaceitimmediately.

•Neverputyourhandsorfeetunderthemower.

•Nevertrytoclearthedischargeareaormower

bladesunlessyoudisengagethepowertakeoff

(PTO)leverandturntheignitionkeytooff.

Alsoremovethekeyandpullthewireoffthe

sparkplug(s).

Ensurethemowerhasthehingedgrassdeectorthat

dispersesclippingstothesideanddowntowardtheturf,

whileinsidedischargemode.

Tomulchgrassclippings,thebafesmustbeinstalled

intothemowerasshowninthefollowingsteps.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (12 pages)

PAGE 1
Form No. 3369-284 Rev A 60 and 72 inch Recycler® Kit Z Master® G3 and GrandStand® Mower Model No. 115-7468 Model No. 115-7469 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Safety Side Discharge or Mulch Grass WARNING Without the grass deflector, discharge cover, or complete grass catcher assembly mounted in place, you and others are exposed to blade contact and thrown debris.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 9 10 Description Use Qty. No parts required – Raise the mower for access. No parts required – Prepare the mower. No parts required – Remove the existing blades. No parts required – Remove the existing baffles.
PAGE 3
1 Raising the Mower for Access (GrandStand Mowers Only) No Parts Required Procedure The front of the mower can be raised and supported on its back for access under the machine for maintenance. DANGER The machine could fall onto someone and cause serious injury or death • Always turn the engine off, set the parking brake, and remove the key before performing any maintenance to the mower. Figure 1 GrandStand Mowers Only 1. Wing nut 2. Battery cover 3.
PAGE 4
Figure 2 GrandStand Mowers Only 1. Cap 2. Piece of plastic 3. Hydraulic tank 7. With two people, raise the front of the mower so it rests on the drive tires and the platform in the up position. Figure 3 GrandStand Mowers Only 8. Perform maintenance on the machine. 1. Ensure the battery is removed 2. With two people, lift the front end of the mower (ensure the mower deck is in the highest position) 2 Preparing the Mower No Parts Required Procedure 1. Thoroughly clean mower deck.
PAGE 5
3 4 Removing the Existing Blades Removing the Existing Baffles No Parts Required No Parts Required Procedure Procedure Note: In the steps below, the bolts are threaded into the mower deck. Remove the nuts first before removing bolts. 1. Remove the flange nuts holding the baffles in place (Figure 5 or Figure 6). 2. Remove the cam lock and washer by unscrewing it from the adjustable flow baffle (Figure 5 or Figure 6). Remove the existing blades from the spindles (Figure 4).
PAGE 6
Figure 6 GrandStand Mowers Only 1. 2. 3. 4. Flange Nut Bolt Left front baffle Adjustable Flow Baffle 5. 6. 7. 8. Figure 7 1. Drill this hole to 3/8 inch diameter Discharge baffle Mower deck Washer Cam lock 2. Drill these holes to 7/16 inch diameter 6 5 Installing the Discharge Plate and Cover Plate Drilling Holes for G3 Mower Decks Parts needed for this procedure: 1 Discharge plate 1 Cover plate 2 Carriage bolt, (3/8 x 1-1/4 inches) Procedure 1 Carriage bolt, (5/16 x 7/8 inch) 1.
PAGE 7
Installing the Baffles Parts needed for this procedure: 1 Left baffle 1 Center baffle 1 Right baffle 7 Flange nut (small flange), (3/8 inch) 6 Carriage bolt (3/8 x 1 inch) 2 Bolt, (3/8 x 1 inch) 1 Flange nut (large flange), (3/8 inch) Procedure Note: Loosely install the baffles to align the baffles with all holes in the mower (Figure 10). 1. Position the right baffle into the mower. G016245 Figure 8 1. Carriage bolt, (3/8 x 1-1/4 inches) 2. Discharge plate 3.
PAGE 8
Figure 10 GrandStand mower deck shown 1. Flange nut (small flange), (3/8 inch) 2. Carriage bolt, (3/8 x 1 inch) 3. Bolt, (3/8 x 1 inch) 4. Left baffle 5. Right baffle 6. Flange nut (large flange), (3/8 inch) 8. Position the center baffle into the mower. 10. Loosely install the center baffle to the right baffle with 1 carriage bolt (3/8 x 1 inch) and 1 flange nut (small flange) (3/8 inch) (Figure 11). 9.
PAGE 9
8 9 Installing the Kickers on 72 inch Mowers Installing the New Blades Parts needed for this procedure: Parts needed for this procedure: 3 Recycler blades 2 Kickers 4 Carriage bolt (5/16 x 7/8 inch) Procedure 4 Lock nut (5/16 inch) Important: The sail part of the blade (i.e., the turned up section) must face the inside of the mower (Figure 13). Procedure 1. Install the new blades to the spindles with curved washers and blade bolts that were previously removed (Figure 13). 1.
PAGE 10
Operation 10 Selecting the Proper Height-of-Cut Tightening all Fasteners Remove approximately one inch or no more than 1/3 of the grass blade when cutting. In exceptionally lush and dense grass you may need to raise the height-of-cut setting or convert to side discharge or bagging operations. No Parts Required Procedure 1. Tighten all nuts and bolts for the baffles (Figure 8, Figure 9, Figure 10 and Figure 11). Mowing in Extreme Conditions 2.
PAGE 11
Notes: 11
PAGE 12