Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 115-7470

FormNo.3371-267RevA

StripingKit

forZMaster

Mowers

ModelNo.115–7470and115–7480

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Righthandbracket1

Lefthandbracket

CarriageBolt(3/8x1inch)

Flangenut(3/8inch)

Installthebrackets.

Roller1

Mountingplatewithshaft

CarriageBolt(3/8x1inch)

Rollerplate1

Flangenut(3/8inch)

Installtheroller.

Note:Determinetheleftandrightsidesofthemachine

fromthenormaloperatingposition.

InstallingtheBrackets

Partsneededforthisprocedure:

1Righthandbracket

Lefthandbracket

CarriageBolt(3/8x1inch)

Flangenut(3/8inch)

Procedure

1.DisengagethePTO,turntheignitionkeytooff,and

removethekey.

2.Waitforallmovingpartstostopbeforeleavingthe

operatingpositionandthensettheparkingbrake.

3.Installtherighthandbrackettotherearofthe

mowerdeckwith2carriagebolts(3/8x1inch)and

2angenuts(3/8inch)(

Figure1).

4.Installthelefthandbrackettotherearofthemower

deckwith2carriagebolts(3/8x1inch)and2ange

nuts(3/8inch)(Figure1).

Figure1

60inmowerdeckshown

1.Carriagebolt(3/8x1inch)3.Flangenut(3/8inch)

2.Lefthandbracket

4.Righthandbracket

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3371-267 Rev A Striping Kit for Z Master® Mowers Model No. 115–7470 and 115–7480 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 Description Right hand bracket Left hand bracket Carriage Bolt (3/8 x 1 inch) Flange nut (3/8 inch) Roller Mounting plate with shaft Carriage Bolt (3/8 x 1 inch) Roller plate Flange nut (3/8 inch) Use Qty. 1 1 4 4 1 1 4 1 4 Install the brackets. Install the roller.
PAGE 2
Installing the Roller 4 Parts needed for this procedure: 1 Roller 1 Mounting plate with shaft 4 Carriage Bolt (3/8 x 1 inch) 1 Roller plate 4 Flange nut (3/8 inch) 5 g017719 Figure 3 60in mower deck shown 1. Flange nut (3/8 inch) 4. Left hand bracket Procedure 2. Roller assembly with roller plates 5. Right hand bracket 1. Install the roller onto the roller plate with the shaft (Figure 2). 3. Carriage bolt (3/8 x 1 inch) 2. Slide the roller plate onto the end of the shaft (Figure 2).
PAGE 3
Operation moisture content of the grass can provide better contrast when mowing at a long/tall height of cut. Experiment with what works best in your situation. Positioning the Roller Striping visibility is affected by the sun position There are 5 positions for the roller. Refer to Figure Figure 4 for the positions to use with the mower deck height-of-cut. This is how the light is reflected on the grass. Position the roller in the maximum up position when not in use.
PAGE 4
The landscape can promote or hinder striping Driving the machine to different cutting areas • The mowing area size has an effect on the final appearance. Large areas can look better when mowed with a large mower. Small areas may not look right when cut with a large mower. • Raise the deck and drive along a previous cut path to transport from one area of the property to another section. • A nice striping pattern can be ruined by driving across the pattern.