Installation Instructions

FormNo.3361-324RevA

ReelTipperKit

forReelmaster6500-D/6700-DTractionUnit

ModelNo.115-8008

InstallationInstructions

InstallingtheSideTipper

Assemblies

Partsneededforthisprocedure:

LHTipperbracketsupport(112-6576-03)

RHTipperbracketsupport(112-6577-03)

Reartipperbracket(100-3892-03)

Rollerpin(75-5400)

Roller(75-5390)

LHpivotrod(105-0126-03)

RHpivotrod(105-0127-03)

Liftchain(5-1096)

Torsionspring(104-1805)

Torsionspring(98-3929)

Hexheadscrew(3/8x1inch)(323-6)

Hexheadscrew(3/8x1-1/4inches)(323-7)

Hexheadscrew(3/8x1-1/2inches)(323-8)

Flatwasher(3256-3)

Flatwasher(3256-24)

Flatwasher(3256-26)

Retainingring(32151-61)

Locknut(3296-39)

Procedure

1.AssemblethepartsasshowninFigure1.

2.Connecttheliftchainstothecuttingunits.

3.Securethepivotrodtothe#2liftarmwithalocknut

andawasher(Figure1).Repeatthisprocedurefor

#3liftarm.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

PAGE 1
Form No. 3361-324 Rev A Reel Tipper Kit for Reelmaster 6500-D / 6700-D Traction Unit Model No.
PAGE 2
Figure 1 1. 2. 3. 4. 5. 6. Hex head screw (3/8 x 1 inch) RH tipper support bracket Flat washer (3256-3) Locknut Hex head screw (3/8 x 1-1/2 inches) Torsion spring 7. 8. 9. 10. 11. 12. RH pivot rod Lift chain Hex head screw (3/8 x 1-1/4 inches) LH pivot rod Torsion spring Flat washer (3256-24) 2 13. 14. 15. 16. 17. 18.
PAGE 3
2 Installing the Front Tipper Assembly Parts needed for this procedure: 1 Stabilizer (105-0138-03) 1 Tipper bracket (108-6706-03) 1 Roller pin (108-6705) 1 Front pivot rod (105–0134-03) 1 Reel roller (108-6707) 1 Chain (93-6738) 1 Torsion spring ((98-3929) 2 Hex head screw (3/8 x 3/4 inches) (3234-1) 1 Hex head screw (3/8 x 1-1/4 inches) (323-7) 2 Hex head screw (1/2 x 1-1/4 inches) (3234-38) 3 Flat washer (3256-24) 2 Flat washer (3256-26) 2 Retaining ring (32151-61) 3 Locknut (32
PAGE 4
Figure 2 1. 2. 3. 4. 5. Stabilizer Tipper bracket Hex head screw (3/8 x 1-1/4 inches) Roller pin Hex head screw (1/2 x 1-1/4 inches) 6. 7. 8. 9. 10. Retaining ring Flat washer (3256-26) Flat washer (3256-24) Locknut Torsion spring 2. Connect the lift chains to the front center cutting unit. 3. Secure the front pivot rod to the lift arm with a locknut and a washer (Figure 2). 4 11. Front pivot rod 12. Chain 13.