Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 117-0940

FormNo.3364-997RevA

CoolantTankKit

ZMaster

RidingMowers

ModelNo.117-0940

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Capassembly

Plastictie1

Installthehosecoolanttank.

Sectionofplasticcovering

Plastictie2

InstallthefanwireprotectionforKubota

PoweredMowersOnly.

InstallingtheHoseand

CoolantTank

Partsneededforthisprocedure:

Capassembly

1Plastictie

Procedure

1.Positionthemachineonalevelsurface,stopthe

engine,andsettheparkingbrake.

2.Unlatchtheseatandliftitup.

3.Thoroughlycleanmowerandtheareaaroundthe

coolanttankbeforeinstallingthiskit.

4.Removetheexistingcoolanttankcapanddiscard.

5.Withthehoseassemblyupsidedown,slidethe

retainerringovertheneckofthecoolantbottle.

Ensurethenewcapandhoseassemblyisupside

downwheninstallingtheretainerring(

Figure1).

Figure1

1.Capwithretainerring

(upsidedowntoinstall

retainerring)

3.Coolanttank

2.Retainerring

6.Foldthecapoverandsnapitontothebottle

(Figure2).Ensurethecapsnapsontightandseals

thecoolantbottle.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3364-997 Rev A Coolant Tank Kit Z Master® Riding Mowers Model No. 117-0940 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 Description Cap assembly Plastic tie Section of plastic covering Plastic tie Use Qty. 1 1 1 2 Install the hose coolant tank. Install the fan wire protection for Kubota Powered Mowers Only.
PAGE 2
1 2 3 4 5 6 Figure 2 1. Fold the cap over 2. Bottle neck with retainer ring 7 7. Attach the end of the hose to the lower cross bar with a plastic tie. Ensure the hose is not kinked and the end of the hose points down (Figure 3). 1 4 7 8 9 g013090 Figure 3 1. Upper cross bar (Do Not use) 2. Ensure the hose end points down 3. Plastic tie 4. Hose (ensure it is not kinked) 5. Front of machine 6. New coolant tank cap 7. Lower cross bar (attach hose here) 8. Side view of the tank and hose 9.
PAGE 3
2 Installing the Fan Wire Protection for Kubota Powered Mowers Only Parts needed for this procedure: 1 Section of plastic covering 2 Plastic tie Procedure 1. Remove the front engine panel (Figure 4). Figure 4 1. Knob 2. Front engine panel Figure 5 2. Remove the existing plastic tie securing the wires before installing the plastic cover. Refer to Figure 5. 1. Wirelead from the wire harness 2. Remove this existing plastic tie 3.
PAGE 4