Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 117-3879

FormNo.3364-880RevA

Roll-OverProtectionSystemKit

2010andAfterZ500RidingMowers

ModelNo.117-3879

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Rollbar,rightsection1

Rollbar,leftsection

Rollbar,centersection1

Bolt,(3/8x1inch)

Curvedwasher

Flangenut,(3/8inch)

Bolt,(1/2x3–1/4inch)

Flangenut,(1/2inch)

InstalltheRolloverProtectionSystem

(ROPS).

Seatlatchcatch

Bolt(5/16x3/4inch)

Locknut(5/16inch)

Replacetheseatlatchcatch.

Seatbeltkit

1Installtheseatbelt.

Seatframe

Locknut(3/8inch)

Bolt(3/8x5inches)

Installthenewseatframe.

InstallingtheRollOver

ProtectionSystem(ROPS)

Partsneededforthisprocedure:

1Rollbar,rightsection

Rollbar,leftsection

1Rollbar,centersection

Bolt,(3/8x1inch)

Curvedwasher

Flangenut,(3/8inch)

Bolt,(1/2x3–1/4inch)

Flangenut,(1/2inch)

Procedure

1.RemovetheexistingROPSfromthemachineframe

anddiscard(

Figure1).

2.Looselyinstalltherightandleftrollbarsectionto

theframe,with8bolts(3/8x1inch),8curved

washers,and8angenuts(3/8inch)(Figure1).

Note:Thecurvewasherconemustbeinstalled

towardthebolthead.

Figure1

3.Installthelanyardclipsontothelongbolts(1/2x

3-1/4inch).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3364-880 Rev A Roll-Over Protection System Kit 2010 and After Z500 Riding Mowers Model No. 117-3879 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty.
PAGE 2
Note: Make sure the bent tab points toward the head of the bolt. Figure 2 4. Lightly oil the ends of the center roll bar section. 5. Loosely install the center roll bar section using 2 bolts (1/2 x 3-1/4 inch) and 2 flange nuts (1/2 inch). Note: Make sure the bolts are installed from the outside of the roll bar. Note: Make sure the lanyard tab is installed as show and points forward. Figure 4 7. Torque all lower fasteners, attached to the machine frame, to 30 ft-lb. 8.
PAGE 3
2 3 Replacing the Seat Latch Catch Installing the Seat Belt Parts needed for this procedure: Parts needed for this procedure: 1 Seat belt kit 1 Seat latch catch 2 Bolt (5/16 x 3/4 inch) Procedure 2 Locknut (5/16 inch) 1. Tilt the seat forward and remove the existing seat belt receiver and retractable belt. Procedure 2. Install the receiver part of the seat belt to the seat frame with a supplied bolt. 1. Tilt the seat forward and remove the existing latch catch. 3.
PAGE 4
7. Install the seat to the new seat frame with the four locknuts and spacers previously removed . 4 Installing the New Seat Frame Parts needed for this procedure: 1 Seat frame 2 Locknut (3/8 inch) 2 Bolt (3/8 x 5 inches) Procedure 1 1. Tilt the seat forward and remove the nut and bolt from the seat retaining rod (Figure 8). 2 3 3 1 2 4 g013062 Figure 9 g013061 1. Seat 2. Seat spacer Figure 8 1. Bolt 2. Seat rod 3. Nut 3. Seat frame 4. Ensure the slot is installed towards the front 8.
PAGE 5
2 1 3 g013058 Figure 10 1. Nut 2. Seat 3. Bolt 9. Install the seat retaining rod with the nut and bolt previously removed (Figure 8). Note: Do not over tighten the nut and bolt to allow the retaining rod to pivot. 10. If needed, attach the two connectors onto the seat switch.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8