Installation Instructions

ManualsBrandsToro ManualsAttachmentsAccessory Installation Kit, Espar Heater Kit for Workman MDE Utility Vehicle

Table Of Contents

FormNo.3372-883RevA

AccessoryInstallationKit

EsparHeaterKitforWorkman

MDEUtilityVehicle

ModelNo.117-4968

InstallationInstructions

Note:ThiskitistobeinstalledincombinationwithanEsparHeaterKitand12VPowerPlugAdapterKit(07318).The

followingproceduresareinstructionsforconguringaWorkmanMDEtoallowtheEsparHeaterKittobeinstalled.

InstructionsfortheinstallationoftheheatercanbefoundwiththeEsparHeaterKit.

Installation

PreparingtheVehicle

NoPartsRequired

Procedure

•Parkthemachineonalevelsurface,settheparkingbrake,

turntheignitionoff,andremovethekey.

•Raisethebedboxtoopenthebatterycircuitbycarefully

removingoneofthebatterycables.Refertoyour

Operator'sManualformoreinformation.

•Removetheseatsandseatbase.Refertotheappropriate

sectionoftheServiceManualformoreinformation.

InstallingtheGastank

Partsneededforthisprocedure:

Gastankassembly

1Breatherhosebarb

1Breatherhose

1Fuellinegrommet

1Fuelline

1Rubberbumper

Strap

Cap

Procedure

1.Locatethegastankinlooseparts.Removetheairvent

anddiscard(

Figure1).

G01 1275

Figure1

1.Gastank

4.Breatherhoseandbarb

2.Fuelline

5.Cap

3.Airvent

2.Installtherubbergrommetoverthefuelline.Install

thefuellineassemblytothegastank(Figure1).

3.Installthehosebarbtothebreatherhose.Installthe

breatherhoseassemblytothegastank(Figure1).

4.Installthegascaptothetank.

5.Removetheplatefromthebottomoftheframeand

discard(Figure2).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3372-883 Rev A Accessory Installation Kit Espar Heater Kit for Workman® MDE Utility Vehicle Model No. 117-4968 Installation Instructions Note: This kit is to be installed in combination with an Espar Heater Kit and 12V Power Plug Adapter Kit (07318). The following procedures are instructions for configuring a Workman MDE to allow the Espar Heater Kit to be installed. Instructions for the installation of the heater can be found with the Espar Heater Kit.
PAGE 2
1 2 1 G011278 G011276 3 Figure 2 1. Plate 6. Install the strap through the slots in the frame (Figure 3). Install the rubber bumper through the hole in the frame as shown. 1 Figure 4 1. Gas tank 3. Strap fastened 2. Strap 8. Wrap the strap around the tank and tighten it to secure the tank to the frame (Figure 4). 3 3 2 G011277 Installing the Wire Harness. Figure 3 1. Strap 3. Rubber bumper Parts needed for this procedure: 2. Slots in frame 1 7.
PAGE 3
2 1 2 3 G011279 3 Figure 5 1. Ring terminal, red 3. Plug 2. Ring terminal, black 1 2. Move to the battery array in the frame box. Remove the protective boots from the positive and negative posts (Figure 6). Remove the nuts from the posts. Install the positive ring lead (Figure 5) on the positive battery posts depicted. Install the negative ring lead (Figure 5) on the negative battery post depicted. G011281 Figure 7 1. Opening in the forward wall of the frame box 2. Wire harness 3.
PAGE 4
• Use the wire to pull the harness forward and up 6. Connect the 12V DC Out wire from the converter to the power wire on the heater kit. through the hole in the center frame channel below the dash (Figure 9). 1 2 G011283 3 Figure 9 1. Hole in the center frame channel below the dash 3. Center channel cap (transparent for clarity) 2. Machine underside • Disconnect the stiff wire or fish tape from the harness. 5.