Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 117-5312

FormNo.3362-196RevA

50inRecyclerKit

forTITANZero-Turn-RadiusRidingMower

ModelNo.117-5312

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemower.

Leftbafe

Rightbafe

Knob4

Curvedwasher

Installtheupperbafe.

Kickerplate3

Phillipsheadscrew(#8x5/8inch)

Installthekickerplates.

Recyclingdecal1Instalthedecal.

Recyclingmowerblade3Installthebladesandmower

PreparingtheMower

NoPartsRequired

Procedure

1.Stoptheengineandremovetheignitionkey.

2.RemovethemowerasdescribedinyourOperator’s

Manual.

3.Turnthemowerupsidedown.

4.Removethemowerbladesasdescribedinyour

Operator’sManual.

InstallingtheBafes

Partsneededforthisprocedure:

Leftbafe

Rightbafe

4Knob

Curvedwasher

Procedure

1.Locatethefourholesinthemowerwherethebafe

mountingstudswillmount(Figure1)andremove

anyfastenersfromthem.

2.Installtheleftbafeintothedecksecuringthestuds

onthebafefromthetopofthemowerusing2

knobsandcurvedwashers(cuppedsidefacingthe

mower)asshowninFigure1andFigure2.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3362-196 Rev A 50in Recycler Kit for TITAN Zero-Turn-Radius Riding Mower Model No. 117-5312 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Use Qty. No parts required – Left baffle Right baffle Knob Curved washer Kicker plate Phillips head screw (#8 x 5/8 inch) 1 1 4 4 3 6 Recycling decal 1 Instal the decal. Recycling mower blade 3 Install the blades and mower 1 Prepare the mower.
PAGE 2
Figure 2 1. Knob 3. Baffle stud coming through the mower 2. Curved washer 3. Slide the right baffle through the discharge opening and secure it using 2 knobs and curved washers (cupped side facing the mower) as shown in Figure 1 and Figure 2. Important: Ensure that the tab on the far right side of the right baffle is outside of the mower and is flush with the mower wall. Figure 1 1. Left baffle 2. Mower 3. Curved washer 4. Knob 5. Tab (must remain outside of the mower) 6.
PAGE 3
4 Installing the Kicker Plates Installing the Decal Parts needed for this procedure: Parts needed for this procedure: 3 Kicker plate 1 6 Phillips head screw (#8 x 5/8 inch) Recycling decal Procedure Procedure Install the decal on left side of mower (Figure 4). 1. Align the three kicker plates with holes toward the top of the deck (Figure 3). The long slope of the kickers must be face inward. Figure 4 1. Recycler decal 2.
PAGE 4
Operation Operating Tips Converting to Side-discharge Operation Selecting the Proper Height-of-Cut Setting to Suit the Conditions Remove approximately one inch or no more that 1/3 of the grass blade when cutting. In exceptionally lush and dense grass you may have to raise the height-of-cut setting another notch or convert to side discharge or bagging operations.