Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 117-5314

FormNo.3362-200RevA

54and60inchRecycler®Kit

forTITAN

Zero-Turn-RadiusRidingMower

ModelNo.117-5313,117-5314

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Rightbafe

Leftbafe

Bafeguard,54inchdecksonly

Locknut(5/16inch)

Carriagebolt(5/16x3/4inch)

Mulchingblade3

InstalltheRecycler®Kiton54inchdecks.

Rightbafe

Leftbafe

Bafeguard,60inchdecksonly

Locknut(5/16inch)

Carriagebolt(5/16x3/4inch)

Decal1

Mulchingblade3

InstalltheRecycler®Kiton60inchdecks.

InstallingtheRecycler®Kiton

54inchDecks

1.Stoptheengineandremovetheignitionkey.

2.RemovethemowerasdescribedinyourOperator’s

Manual.

3.Turnthemowerupsidedown.

4.Removetheexistingmowerbladesinstalledonyour

deck.RefertotheRemovingtheBladessectionin

theOperator’sManualformoreinformation.

5.Locatethecutoffbafeatthesidedischarge

openingonthe54inchmowerdeck(Figure1).

Figure1

1.Carriagebolt,existing3.Cutoffbafe,existing

2.Rearholesinthe

dischargeplate

4.Locknut,existing

6.Removethefastenerssecuringthecutoffbafeto

thedeckandremovethecutoffbafe.

Note:Savethecutoffbafeforconvertingbackto

sidedischarge.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3362-200 Rev A 54 and 60 inch Recycler® Kit for TITAN® Zero-Turn-Radius Riding Mower Model No. 117-5313, 117-5314 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty.
PAGE 2
7. Install the fasteners into the same holes in the deck they were originally removed from. This ensure no holes are left open when the deck is operated. 1 Open holes in the mower expose you and others to thrown debris. Debris thrown out of holes in the mower can cause injury. • Never operate the mower without hardware mounted in all holes in the mower. • Install hardware in mounting holes when the baffle is removed. 2 G010704 3 Figure 3 8.
PAGE 3
12. Tighten all fasteners. 13. Install the left baffle to the mower deck as shown in Figure 5. Use three lock nuts (5/16 inch) to secure the welded posts of the right baffle to the top of the mower deck at the center, left of center and left positions. Hand tighten the fasteners. 1 1 2 G010705 3 Figure 5 1. Lock nut (5/16 inch) 2. Carriage bolt (5/16 x 3/4 inch) 3. Left baffle 14. Locate a carriage bolt (5/16 x 3/4 inch) and a lock nuts (5/16 inch) from loose parts.
PAGE 4
Installing the Recycler® Kit on 60 inch Decks 8. Install the right baffle to mower deck as shown in Figure 8. Use three lock nuts (5/16 inch) to secure the welded posts of the right baffle to the top of the mower deck at center, right of center and right positions. Hand tighten the fasteners. 1. Stop the engine and remove the ignition key. 2. Remove the mower as described in your Operator’s Manual. 3. Turn the mower upside down. 4. Remove the existing mower blades installed on your deck.
PAGE 5
3 1 G010716 1 2 Figure 9 1. Carriage bolts (5/16 x 3/4 inch) 2. Baffle guard, 60 inch 3. Lock nut (5/16 inch) Figure 11 1. Decal 16. Install the mulching mower blades located in loose parts. Refer to the Installing the Blades section in the Operator’s Manual for more information. 10. Locate a carriage bolt (5/16 x 3/4 inch) and lock nut (5/16 inch) from loose parts. Install the carriage bolt and lock nut through rear wall of the mower deck and right baffle to secure the baffle to the deck. 11.
PAGE 6
Operation Operating Tips Selecting the Proper Height-of-Cut Setting to Suit the Conditions Remove approximately one inch or no more that 1/3 of the grass blade when cutting. In exceptionally lush and dense grass you may have to raise the height-of-cut setting another notch or convert to side discharge or bagging operations.
PAGE 7
Notes: 7
PAGE 8