Installation Instructions

ManualsBrandsToro ManualsAttachmentsOverflow Tank Kit, Groundsmaster 7200/7210 Traction Unit

FormNo.3434-930RevA

OverowTankKit

Groundsmaster

7200/7210TractionUnit

ModelNo.117-5570

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removethebreather.

Hose1

Hoseclamp1

Hoseclamp(5/16inchhose)

Screw(5/16x3-1/4inch)

Washer2

Nut(5/16inch)

InstalltheoverowtankwithKubota

engines.

Bolt(1/4x3/4inch)

Nut(1/4inch)

Bracket1

Hose1

Hoseclamp1

Hoseclamp(5/16inchhose)

Screw(5/16x2inch)

Washer2

Nut(5/16inch)

InstallingtheoverowtankwithYanmar

engines.

Grommetplug

Connectthehoses.

PreparingtheMachine

NoPartsRequired

PreparingtheMachine

1.Parkthemachineonalevelsurface.

2.MovetheleverstotheNEUTRALposition.

3.Lowerallattachments(ifequipped).

4.Engagetheparkingbrake.

5.Shutofftheengineandremovethekey.

6.Disconnectthebattery;refertoyourmachine

Operator’sManual.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3434-930*A

Summary of content (8 pages)

PAGE 1
Form No. 3434-930 Rev A Overflow Tank Kit Groundsmaster® 7200/7210 Traction Unit Model No. 117-5570 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Qty. Use No parts required – Prepare the machine. No parts required – Remove the breather.
PAGE 2
3 Removing the Breather Installing the Overflow Tank with Kubota© Engines No Parts Required Parts needed for this procedure: Procedure 1. Locate the hydraulic tank breather mounted to the frame tube just ahead of the air cleaner mounting bracket (Figure 1). Remove the cable tie securing the breather to the frame tube. 1 Hose 1 Hose clamp 1 Hose clamp (5/16 inch hose) 2 Screw (5/16 x 3-1/4 inch) 2 Washer 2 Nut (5/16 inch) Procedure 1.
PAGE 3
4 Installing the Overflow Tank with Yanmar© Engines Parts needed for this procedure: 2 Bolt (1/4 x 3/4 inch) 2 Nut (1/4 inch) 1 Bracket 1 Hose 1 Hose clamp 1 Hose clamp (5/16 inch hose) 2 Screw (5/16 x 2 inch) 2 Washer 2 Nut (5/16 inch) g011178 Figure 3 1. Accumulator 2. Screw, 5/16 x 3–1/4 inch 3. 3. Washer 4. Flange nut Connect the breather hose to the side fitting on the accumulator with a hose clamp (Figure 4). Procedure 1.
PAGE 4
5. Connect the new hose to the bottom fitting on the accumulator with a hose clamp (Figure 7). 5 Connecting the Hoses Parts needed for this procedure: 1 Grommet plug Procedure 1. g304842 Figure 6 1. Washer 2. Screw (5/16 x 2 inches) 3. Unlatch and raise the seat. Locate the hose that goes from the elbow fitting on the hydraulic tank to the tube on the transmission (Figure 8). 3. Accumulator 4.
PAGE 5
g011181 Figure 9 1. Grommet plug 5. Route the new hose to the transmission tube (Figure 10). Note: Keep the hose away from any hot, sharp or moving parts. g011174 Figure 10 1. Transmission tube 2. New hose 6. Secure the hose to the transmission tube with a hose clamp (Figure 10). 7. Lower the seat. 8. Check the hydraulic fluid level in the reservoir. If the fluid level is low, add fluid until the level is between the marks on the dipstick.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8