Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 117-8560

FormNo.3365-248RevA

StripingKit

GrandStand

Mowerwith36-inchor40-inchCuttingUnit

ModelNo.117-8560

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemower.

Nopartsrequired

–

Drilltheholesforthechains.

Mountingbracket2

Bolt,(3/8x1inch)

Carriagebolt,(3/8x1inch)

Flangenut,(3/8inch)

Washer2

Installthemountingbrackets.

Rollerassembly1

Spring

Clevispin

Hairpincotterpin2

Installtherollerassemblytostriper

bracketmounts.

Nopartsrequired

–

Connectthechains.

PreparingtheMower

NoPartsRequired

Procedure

1.Thoroughlycleanthemachine.Alldebrismustbe

removedtoensurethekitwilltproperly.

2.Repairallbentordamagedareasandreplaceany

missingparts.

3.Raisetheplatformandverifythelatchissecurely

engagedtoholdtheplatformup.

DrillingtheHolesforthe

Chains

NoPartsRequired

Procedure

1.Locatethepapertemplateatthebackofthis

instructionsheetandcutitout.

2.Cutoutthecirclesfortherubberbumpers.

3.Placethetemplateoverthetwoinsiderubber

bumpersunderneaththeplatformbar(Figure1).

4.Makethelocationforthetwoholesanddrilltwo

9/16inchdiameterholesintotheplatformbar

(Figure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3365-248 Rev A Striping Kit GrandStand® Mower with 36-inch or 40-inch Cutting Unit Model No. 117-8560 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Use Qty. No parts required – Prepare the mower. No parts required – Drill the holes for the chains.
PAGE 2
1 2 4 1 2 3 3 g013334 g013332 Figure 2 Figure 1 1. Drill two 9/16 inch diameter holes (drill from underneath to avoid interference issues) 2. Inside rubber bumper 1. Use carriage bolts or bolts (3/8 x 1 inch) 2. Mounting bracket 3.
PAGE 3
5 Connecting the Chains No Parts Required 1 Procedure 1. Hold the operator platform while releasing the platform latch. Lower the platform down until the chain ends can be snapped into the holes previously drilled into the platform bar (Figure 5). 2. Snap the chain end into the holes previously drilled into the platform bar (Figure 5). 2 4 1 3 5 g013329 Figure 3 1. Hairpin cotter pin 2. Left spring long finger 3. Right spring long finger 4. Clevis pin 5. Roller assembly 4.
PAGE 4
Operation Operating Tips Raising the Roller Effective striping is influenced by grass condition and grass type With the platform down, raise the roller up and rotate the lift handle over the platform (Figure 6). 1 • Limp grass where wheel tracks are very visible is usually good for striping. • Stiff grass where wheel tracks are less visible will usually produce poor striping. 2 • Cool season grass types found in northern areas are usually good for striping.
PAGE 5
Lawn condition affects striping visibility • On week 3 use a cross–grain striping pattern. • On weeks 4 and 5 follow with repeating the original pattern. After the primary striping pattern grain is established, you may alternate the pattern each week to establish a checkerboard or a plaid style of mowing pattern. • Large flat areas usually provide better striping contrast than on slopes or areas with a lot of trimming and edging. • Mowing in morning dew can produce good striping contrast.
PAGE 6
Notes: 6
PAGE 7
Cut along this line 1.00 Scale Cut this hole out for rubber bumper . 1-1/4 inches (31.8mm) Cut along this line Drill this hole 9/16 inch dia. Drill this hole 9/16 inch dia. Cut this hole out for rubber bumper .
PAGE 8