Installation Instructions

ManualsBrandsToro ManualsRiding ProductsCE Kit, 2010 and After Groundsmaster 5900/5910 Traction Unit

FormNo.3363-186RevB

CEKit

2010andAfterGroundsmaster

5900/5910TractionUnit

ModelNo.117-9449

InstallationInstructions

InstalltheHoodLatch

Partsneededforthisprocedure:

1LatchKey

1Latch

1LatchBracket

CarriageScrew

3FlangeNut

Procedure

1.Parkthemachineonalevelsurface,lowerthedecks,

engagetheparkingbrakeandturntheengineoff.

Removethekeyfromtheignitionswitch.

2.Unlatchandraisethehood.

3.Removetheplugfromthesquareholeintheright

sideofthehood.Discardtheplug.

4.Removethelockingnutfromthelatchassembly

(Figure1).

5.Installthelockinglatchthroughthesquareholein

therightsideofthehood(Figure1).Thecatch

mustbepositionedinsidethehoodandpointing

downward.

Figure1

1.Latchkey

4.Carriagescrew

2.Latch5.Flangenut

3.Latchbracket

6.Installthelockingnutontothelatchtosecureitto

thehood.

7.Locatethe(3)holesintherightsideoftheradiator

support(Figure1).Mountthelatchbrackettothe

radiatorsupportwith(3)carriagescrewsandange

nuts.PositionthelatchbracketasshowninFigure1.

8.Closethehoodslowlytoseeiflatchcatches.If

itdoesnot,loosenthescrewssecuringthelatch

brackettotheradiatorsupportandadjustthebracket

asnecessary.Tightenthescrewsandverifythelatch

catches.

9.Usethekeytolock/unlocklatch.Storethekeyina

convenientandmemorableplace.

InstalltheSidePanelHardware

Partsneededforthisprocedure:

Screw(5/16x3/4inch)

Pushnut(5/16inch)

Hexnut(5/16inch)Forassemblingpushnutonly

Procedure

1.Removetheexistinghardwaresecuringtheside

paneltothemachineanddiscard(

Figure2).Remove

thesidepanel.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3363-186 Rev B CE Kit 2010 and After Groundsmaster® 5900/5910 Traction Unit Model No. 117-9449 Installation Instructions 6. Install the locking nut onto the latch to secure it to the hood. 1 7. Locate the (3) holes in the right side of the radiator support (Figure 1). Mount the latch bracket to the radiator support with (3) carriage screws and flange nuts. Position the latch bracket as shown in Figure 1.
PAGE 2
1 after removal. Loosen all of the fasteners on each cover a few turns so that the cover is loose but still attached, then go back and loosen them until the cover comes free. This will prevent you from accidentally stripping the bolts free of the retainers. g011939 2 3 Install the Speed Limiter 3 Figure 2 1. Hood 2. Side panel Parts needed for this procedure: 3. Screw (5/16 x 3/4 inch) 2.
PAGE 3
Note: Do not install the plastic plugs until the spacer and stop plates are positioned under the switches. 3. While aligning the mounting holes, position the stop plate onto the spacer plate. The stop plate should be positioned under the switches (Figure 5). 4. Secure the plates to the console with the plastic plugs (Figure 5). B. Turn the ignition key to the RUN position.
PAGE 4
1 the seat and the ignition key is in the RUN position. 2 C. While using the High/Low Range diagnostic screen on the InfoCenter, move the position switch bracket just until the front Deck Down input reads OFF. Refer to the Groundsmaster 5900 Service Manual for information on InfoCenter operation. 3 This is the point in the raise sequence of the deck where the deck position switch will shut off the deck motor. g011942 Figure 8 D. Tighten the switch bracket mounting fasteners.
PAGE 5
3 2 1 G009446 Figure 9 1. CE compliance decal (Part 3. CE Warning decal (Part No. 117–2761) No. 117–2766, apply over existing decal) 2. Production year decal (included in traction unit loose parts) 2. Dampen the area with water or mildly soapy water. 3. Peel the backing from the decals and install the decals at the locations shown in Figure 9. 4. Squeegee across the surface of each decal, starting at the center and working toward the edges, using overlapping strokes.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8