Installation Instructions

ManualsBrandsToro ManualsAttachmentsOil Cooler Kit, Greensmaster 3300 Series Traction Unit

FormNo.3369-735RevB

OilCoolerKit

Greensmaster3300SeriesTractionUnit

ModelNo.119-1691

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Largehosestrapholder1

Smallhosestrapholder

Hex-washer-head,self-tappingbolt(3/8

x3/4inch)

Spacer

Straightadaptertting

90-degreehydraulictting

90-degreetting

Hoseclamp3

Lowerhose1

Pushlockhoseassembly1

Hydraulichoseassembly1

Rubbergrommet4

Installthettingsandroutethehoses.

Oilcoolerfanwireharness

Relay1

Hex-headbolt(1/4x5/8inch)

Hex-angenut(1/4inch)

15-ampbladefuse

Bushing1

Installtheoilcoolerfanwireharness.

Rubbergrommet2

Oilcoolersupport

Tapbolt(1/2x4inch)

Wireformbrace

Hosewireform

Hex-head-angebolt(5/16x1inch)

Flangenut(5/16inch)

Nut(Tinnerman)

Hex-headbolt(1/4x5/8inch)

Hex-angenut(1/4inch)

Mounttheoilcoolersupportand

wireformbracing.

Oilcooler

Electricfan

Screw

Flatwasher4

Lockwasher4

Squarenut

Nut(Tinnerman)

Hoseclamp2

Hex-head-angebolt(5/16x1inch)

Assembleandinstallthefanandoil

coolerassembly.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3369-735 Rev B Oil Cooler Kit Greensmaster 3300 Series Traction Unit Model No. 119-1691 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 2 3 4 5 © 2013—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Qty.
PAGE 2
Procedure 6 Description Use Qty. 1 2 2 2 2 Oil cooler screen Wing screw Retainer nut Clip Cable tie Finish the installation. 1 Draining the Hydraulic Oil Tank No Parts Required Procedure WARNING Figure 1 Hydraulic fluid escaping under pressure can penetrate skin and cause injury. 1. Hydraulic oil tank • Ensure that all hydraulic fluid hoses and lines are in good condition and that all hydraulic connections and fittings are tight before applying pressure to the hydraulic system.
PAGE 3
2 Installing the Fittings and Routing the Hoses Parts needed for this procedure: 1 Large hose strap holder 1 Small hose strap holder 3 Hex-washer-head, self-tapping bolt (3/8 x 3/4 inch) 1 Spacer 1 Straight adapter fitting 2 90-degree hydraulic fitting 1 90-degree fitting 3 Hose clamp 1 Lower hose 1 Push lock hose assembly 1 Hydraulic hose assembly 4 Rubber grommet Procedure 1.
PAGE 4
Figure 2 1. 90-degree hydraulic fitting 7. Lower hose 13. Hydraulic oil manifold block 2. Hose clamp 8. Spacer 14. Straight adapter fitting 9. Large hose strap holder 15. Push lock hose assembly 3. Oil cooler 4. Hydraulic oil tank 10. Hydraulic line 16. Small hose strap holder 5. 90-degree fitting 11. Hydraulic hose assembly 17. Machine frame 6. Hex-washer-head, self-tapping bolt (5/16 x 3/4 inch) 12. Rubber grommets (2) 18. Cable tie 5.
PAGE 5
Note: Discard the hose. 9. Install the hydraulic hose (from loose parts) onto a 90-degree fitting on the bottom of the hydraulic tank. 3 Installing the Oil Cooler Fan Wire Harness Parts needed for this procedure: 1 Oil cooler fan wire harness 1 Relay 1 Hex-head bolt (1/4 x 5/8 inch) 1 Hex-flange nut (1/4 inch) 1 15-amp blade fuse 1 Bushing Procedure Figure 3 1. Connect kit wire harness to the main wire harness on the right-hand side of the machine.
PAGE 6
B. Mount the oil cooler support by its flange to the machine frame with 2 tap bolts (1/2 x 4 inches). 4 Note: Torque the bolts to 100 to 110 ft-lb. Mounting the Oil Cooler Support and Wireform Bracing 3. Install the wireform brace by securing the upper end to the frame and the lower end to the cylinder mount using 2 hex-head flange bolts (5/16 x 1 inch), a flange nut (5/16 inch), and a Tinnerman nut (Figure 4).
PAGE 7
6 Finishing the Installation Parts needed for this procedure: 1 Oil cooler screen 2 Wing screw 2 Retainer nut 2 Clip 2 Cable tie Procedure 1. Connect the other ends of the hydraulic hoses to the hydraulic line and the manifold block, respectively (Figure 6). Figure 5 1. Hex-head flange bolt (5/16 6. Square nut x 1 inch) 2. Screw (#10) 7. Electric fan 3. Lock washer 8. Tinnerman nut (5/16 inch) 4. Flat washer 9. Bushing 5. Oil cooler 10. Oil cooler support 2.
PAGE 8
Maintenance 5. Attach the oil cooler screen to the oil cooler support with 2 wing screws, 2 retainer nuts, and 2 clips (Figure 6). Clean the system every year (clean the screens), or more often, if necessary. 6. Verify that the system works: When you engage the reels, the fan should turn on.