Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 119-3454

FormNo.3365-178RevA

BaggerFinishingKit

TITANZX6000SeriesZero-Turn-RadiusRidingMower

ModelNo.119-3454

InstallationInstructions

ThiskitrequirestheBaggerKittocompleteinstallation.Contact

yourAuthorizedServiceDealerorthemanufacturerCustomer

Servicetoobtainthenecessaryparts.Formoreinformation,visitus

atwww.Toro.com.

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaof

potentialdanger.Replaceanydecalthatisdamagedorlost.

110-6691

1.Thrownobjecthazard—keepbystandersasafedistance

fromthemachine.

2.Thrownobjecthazard,mower—donotoperatewithoutthe

deector,dischargecover,orgrasscollectionsystemin

place.

3.Cutting/dismembermentofhandorfoot—stayawayfrom

movingparts.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3365-178 Rev A Bagger Finishing Kit TITAN ZX6000 Series Zero-Turn-Radius Riding Mower Model No. 119-3454 Installation Instructions This kit requires the Bagger Kit to complete installation. Contact your Authorized Service Dealer or the manufacturer Customer Service to obtain the necessary parts. For more information, visit us at www.Toro.com.
PAGE 2
Installation 3 1 Installing the Chute Installing the Bagger Frame Parts needed for this procedure: Parts needed for this procedure: 1 Bagger frame assembly (60 inch deck) Procedure This Bagger Finishing Kit contains a new Bagger Frame Assembly which is used for units with 60 inch decks only. The Bagger Kit comes with a Bagger Frame Assembly that should be discarded and replaced with the one included with this Bagger Finishing Kit.
PAGE 3
2 front wall of the mower deck. Secure horizontal post to the front wall of the deck using a lock nut. 1 5. Install the chute to the deck. Make sure the opening in top of the chute aligns with the exposed post on the deck top and the forward vertical plate mates with the folded metal bracket of the chute. 4 1 G013097 2 5 3 G013095 Figure 1 1. Deflector assembly 4 4. Carriage bolt (existing), reuse 5. Carriage bolt (existing), retain 2. Lock nut (existing), retain 3.
PAGE 4
G013098 2 1 2 G010641 3 1 Figure 4 1. Retaining clasp 2. Flexible latch 5 4 4 Figure 5 Connecting with the Discharge Tube 1. Discharge tube, curved 4. Peg end 5. Rubber strap 2. Opening in bagger top 3. Discharge tube, flared end No Parts Required 2. Slide the flared end of the discharge tube over the end of the chute. Move the rubber retaining strap on the chute snaps over the peg on the discharge tube to secure it (Figure 5). Procedure 1.
PAGE 5
Maintenance Removing the Finishing Kit Whenever the bagger kit is removed, the finishing kit should be removed using the following procedure. Retain all parts for future installation. 1. Remove the discharge tube from the machine and install the discharge cover. WARNING An uncovered discharge opening could allow the lawn mower to throw objects in the operator or bystander’s direction and result in serious injury. Also, contact with the blade could occur.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8