Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 119-3455

FormNo.3365-174RevA

60inRecycler

Kit

TITANZero-Turn-RadiusRidingMower

ModelNo.119-3455

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Rightbafe

Leftbafe

Fillerplate(2010decksanduponly)

Bafeguard

Locknut(5/16inch)

Carriagebolt(5/16x3/4inch)

Decal1

Mulchingblade3

InstalltheRecycler®Kit

InstallingtheRecycler®Kit

ForDecksfromModelYear2009

Formachinewithmowerdecksfrommodelyear2010

andnewerskiptothenextsectionfortheinstallation

procedures.

1.Stoptheengineandremovetheignitionkey.

2.RemovethemowerasdescribedinyourOperator’s

Manual.

3.Turnthemowerupsidedown.

4.Removetheexistingmowerbladesinstalledonyour

deck.RefertotheRemovingtheBladessectionin

theOperator’sManualformoreinformation.

5.Locatethecut-offbafeatthesidedischarge

openingonthemowerdeck(

Figure1).

G010714

Figure1

1.Locknut,existing

3.Carriagebolt,existing

2.Cut-offbafe,existing

6.Removethefastenerssecuringthecut-offbafeto

thedeckandremovethecut-offbafe.

Note:Savethecut-offbafeforconvertingbackto

sidedischarge.

7.Installthefastenersintothesameholesinthedeck

theywereoriginallyremovedfrom.Thisensureno

holesareleftopenwhenthedeckisoperated.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3365-174 Rev A 60in Recycler® Kit TITAN Zero-Turn-Radius Riding Mower Model No. 119-3455 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty.
PAGE 2
3 DANGER Open holes in the mower expose you and others to thrown debris. Debris thrown out of holes in the mower can cause injury. • Never operate the mower without hardware mounted in all holes in the mower. • Install hardware in mounting holes when the baffle is removed. 1 G010716 1 2 Figure 3 8. Install the right baffle to mower deck as shown in Figure 2.
PAGE 3
Figure 5 1. Decal 16. Install the mulching mower blades located in loose parts. Refer to the Installing the Blades section in the Operator’s Manual for more information.
PAGE 4
For Decks from Model Year 2010 and Up. For machine with mower decks from model year 2009 refer to the previous section for the installation procedures. 1 1. Stop the engine and remove the ignition key. 2. Remove the mower as described in your Operator’s Manual. 2 3. Turn the mower upside down. 4. Remove the existing mower blades installed on your deck. Refer to the Removing the Blades section in the Operator’s Manual for more information. 3 G013149 Figure 7 1. Lock nut, existing 2. Filler plate 5.
PAGE 5
14. Tighten all fasteners. 9. Locate the baffle guard in loose parts. Use two carriage bolts (5/16 x 3/4 inch) and two lock nuts (5/16 inch) to the deck to secure the baffle guard to the right baffle and the mower deck as shown in Figure 9. Hand tighten the fasteners. 15. Remove the backing paper and apply decal to the discharge side of the mower (Figure 11). Smooth it from the center to the edges to remove any air bubbles. 3 1 G010716 1 2 Figure 9 1. Carriage bolts (5/16 x 3/4 inch) 2.
PAGE 6
Operation Operating Tips Selecting the Proper Height-of-Cut Setting to Suit the Conditions Remove approximately one inch or no more that 1/3 of the grass blade when cutting. In exceptionally lush and dense grass you may have to raise the height-of-cut setting another notch or convert to side discharge or bagging operations.
PAGE 7
Notes: 7
PAGE 8