Installation Instructions

ManualsBrandsToro ManualsRiding ProductsCase Drain Hose Kit, Greensmaster 3150 Traction Unit

FormNo.3368-436RevA

CaseDrainHoseKit

Greensmaster

3150and3250-DTractionUnits

ModelNo.119-3565

ModelNo.119-3566

InstallationInstructions

Installation

DrainingtheHydraulic

Reservoir

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface,lowerthecutting

units,settheparkingbrake,turntheengineoffand

removethekeyfromtheignitionswitch

2.Disconnectthehosefromthebottomoftheright

sideofthereservoir(

Figure2orFigure3).Drain

thehydraulicoilintoacleancontainersoitcanbe

re-used.Donotreinstallthehosetothereservoir

afteralltheoilhasbeendrained.

Important:Takecarenottocontaminateoilif

youaregoingtoreuseit.Averysmallamount

ofdirtordebriscanseverelydamagehydraulic

system.

Note:OntheGreensmaster3150,thehosewill

beconnectedtoanadaptedtting.Afteralltheoil

isdrainedfromthereservoir,removetheadapter

ttingandO-ringfromthereservoir(

Figure1).

Figure1

1.Adaptertting

InstallingtheCaseDrainHose

Kit

Partsneededforthisprocedure:

Teetting

O-ring

90degreeelbowtting

O-ring

1Hose

O-ring

Procedure

1.Removetheplugfromthesideofthepump.

2.Installthe90degreeelbowttingtothe

pump,positioningasshowninFigure2forthe

Greensmaster3150orFigure3fortheGreensmaster

3250.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3368-436 Rev A Case Drain Hose Kit Greensmaster® 3150 and 3250-D Traction Units Model No. 119-3565 Model No. 119-3566 Installation Instructions Installation 1 Draining the Hydraulic Reservoir No Parts Required Procedure 1. Park the machine on a level surface, lower the cutting units, set the parking brake, turn the engine off and remove the key from the ignition switch 2. Disconnect the hose from the bottom of the right side of the reservoir (Figure 2 or Figure 3).
PAGE 2
Note: Before installing any hydraulic fittings or hoses, make sure the correct O-rings are in position and lubricated with hydraulic oil. 4. Connect the hose to the tee fitting and the elbow fitting. Route the hose as shown in the figures. 5. Connect the existing hose to the tee fitting. 3. Connect the tee fitting to the reservoir, positioning as shown in Figure 2 for the Greensmaster 3150 or Figure 3 for the Greensmaster 3250. Figure 2 Greensmaster 3150 1. Tee fitting 2. Existing hose 3. New hose 4.
PAGE 3
Figure 3 Greensmaster 3250 1. Tee fitting 2. New hose 3. Existing hose 4. 90 degree elbow fitting 4. Carefully operate all of the machines hydraulic functions to ensure that nothing contacts the hoses or fittings. Make any required adjustments to the hoses or fittings. 3 Completing the Installation 5. Check the hydraulic oil again and replenish if required. No Parts Required Procedure 1. Check the position of each fitting and tighten securely. Use a back up wrench on the fittings when appropriate. 2.
PAGE 4