Installation Instructions

ManualsBrandsToro ManualsAttachmentsFuel Pump Relocation Kit with Pump, Greensmaster 3150 2-Wheel Drive Traction Unit

FormNo.3365-651RevA

FuelPumpRelocationKit

Greensmaster

31502-WheelDriveTractionUnit

ModelNo.119-4121

ModelNo.119-4123

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Fuelpump(forkit119–4123only)

Pumpmountingbracket1

Flangescrew2

Hose(15inches)

Hose(23inches)

Hose(42inches)

InstalltheNewFuelPump

InstallingtheNewFuelPump

DANGER

Incertainconditions,gasolineisextremely

ammableandhighlyexplosive.Areorexplosion

fromgasolinecanburnyouandothersandcan

damageproperty.

•Neversmokewhenhandlinggasoline,andstay

awayfromanopenameorwheregasoline

fumesmaybeignitedbyaspark.

•Performthisprocedurewhentheengineiscold

andinawellventilatedarea.

•Wipeupanygasolinethatspills.

WARNING

Gasolineisharmfulorfatalifswallowed.Long-term

exposuretovaporscancauseseriousinjuryand

illness.

•Avoidprolongedbreathingofvapors.

•Keepfaceawayfromnozzleandgastankor

conditioneropening.

•Keepgasawayfromeyesandskin.

1.Allowtheenginetocompletelycooldown.

2.Removetheaircleanercoverandtheaircleaner

fromtheengine(Figure1).

G014024

Figure1

1.Aircleanercover

2.Oldfuelpumplocation

3.Removethe5existingboltsholdingtheaircleaner

bodytothecarburetor(Figure2).

G014039

Figure2

1.Removeexistingbolts

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3365-651 Rev A Fuel Pump Relocation Kit Greensmaster® 3150 2-Wheel Drive Traction Unit Model No. 119-4121 Model No. 119-4123 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Description Fuel pump (for kit 119–4123 only) Pump mounting bracket Flange screw Hose (15 inches) Hose (23 inches) Hose (42 inches) Use Qty.
PAGE 2
4. Remove the two bolts holding the fuel pump to the engine. Install the bolts back into the holes. 5. Remove the two bolts on the other side of the engine. Save these bolts 6. Install the new bracket with the 2 new bolts (Figure 3). 7. Flip the fuel pump over and install the fuel pump to the new bracket with the 2 bolts removed from the engine (Figure 3). 1 2 3 and to the middle port on the fuel pump (Figure 4). Install the hose clamps. 1 2 4 5 4 G014037 6 3 2 Figure 4 7 1. Long fuel hose 2.
PAGE 3
15. Remove the long fuel line and clamp from the fuel filter, which is located on the right side of the machine. 16. Remove the long fuel hose and clamp from the fuel pump (Figure 5). 17. Loosen the R-clamp on the machine and remove the long fuel hose. 18. Route the new long fuel hose from fuel pump, behind the battery hold down clamp, through the R-clamp and to the fuel filter (Figure 5). 19. Install the fuel clamps onto the new long fuel hose. 20.
PAGE 4