Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 119-4240

FormNo.3368-137RevA

CEKit

forModel78551,78552or78553BlowerandDriveKitfora48in,

52inor60inBaggingSystem

ModelNo.117-3825

ModelNo.117-3826

ModelNo.119-4240

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Note:Thiskitneedstobeinstalledonmodel78551,78552or78553BlowerandDriveKittocreateaCEbagger.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemower.

Warningdecal1

Covermissingdecal

Installthedecals.

Blowercover1

Bolt(1/4x3/4inch)

Washer(1/4inch)

Washer(5/16inch)

Plasticplug1

Pushnut(1/4inch)

Installthecovers.

Leftguard

Backguard1

Frontguard1

Lowerguard1

Bolt(5/16x3/4inch)

Flangenut(5/16inch)

Installtheguards.

Muferguard

Installthemuferguard.

PreparingtheMower

NoPartsRequired

Procedure

1.Thoroughlycleanmowerdeck.Alldebrismustbe

removedtoensurethekitwilltproperly.

2.Repairallbentordamagedareasandreplaceany

missingparts.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3368-137 Rev A CE Kit for Model 78551, 78552 or 78553 Blower and Drive Kit for a 48in, 52in or 60in Bagging System Model No. 117-3825 Model No. 117-3826 Model No. 119-4240 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Note: This kit needs to be installed on model 78551, 78552 or 78553 Blower and Drive Kit to create a CE bagger. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
3 Installing the Decals Installing the Covers Parts needed for this procedure: Parts needed for this procedure: 1 Warning decal 1 Blower cover 1 Cover missing decal 1 Bolt (1/4 x 3/4 inch) 1 Washer (1/4 inch) 1 Washer (5/16 inch) 1 Plastic plug 1 Push nut (1/4 inch) Procedure 1. Remove the existing blower cover (Figure 2). Save the hardware. 2. Clean the area where the decals will go (Figure 1). 3. Install the decals as shown in Figure 1. Procedure 1.
PAGE 3
4 Installing the Guards Parts needed for this procedure: 7 8 1 Left guard 1 Back guard 1 Front guard 1 Lower guard 1 Bolt (5/16 x 3/4 inch) 1 Flange nut (5/16 inch) Procedure g013159 1. Remove the existing hardware around the blower for the left guard, lower guard and back guard (Figure 4 or Figure 5). Save all existing hardware Figure 2 For model 78551 (48inch (122cm)) and 78552 (52inch (132cm)) 1. 2. 3. 4. Existing hardware New blower cover Bolt (1/4 x 3/4 inch) Washer (5/16 inch) 5. 6.
PAGE 4
1 9 g016066 Figure 4 For model 78551 (48inch (122cm)) and 78552 (52inch (132cm)) 1. Existing hardware 2. Left guard 3. Back guard, 52 inch (132cm) 4. Flange nut (5/16 inch) Figure 5 For model 78553 (60 inch (152 cm)) 6. Front guard 7. Lower guard 8. Existing nuts 1. 2. 3. 4. 9. Back guard, 48 inch (122cm) 5. Bolt (5/16 x 3/4 inch) 4 Existing hardware Left guard Back guard Flange nut (5/16 inch) 5. Bolt (5/16 x 3/4 inch) 6. Front guard 7.
PAGE 5
Installing the Muffler Guard Parts needed for this procedure: 1 Muffler guard Procedure 1. Remove the existing muffler guard and save the hardware. Save the existing muffler guard for use when the bagger is removed. 2. Install the new muffler guard with the previously removed hardware (Figure 6). Figure 6 1. Carriage bolt 2. Flange nut 3.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8