Installation Instructions

ManualsBrandsToro ManualsAttachmentsDeck Lock Kit, Groundsmaster 4500-D/4700-D Traction Unit

FormNo.3442-456RevA

DeckLockKit

Groundsmaster

4500-D/4700-DTractionUnit

ModelNo.119-8641

InstallationInstructions

Installation

Thiskitautomaticallypreventsunevensettlingofthe

mowerdecks.

Note:Determinetheleftandrightsidesofthe

machinefromthenormaloperatingposition.

InstallingaDeck-Lock

ManifoldfortheNumber1

LiftArm

Partsneededforthisprocedure:

Rightmanifoldassembly(PartNo.119-8631)

Straighthydraulictting

90-degreehydraulictting

Selftappingscrew(1/4x1-3/4inch)

1Hydraulichose

Procedure

1.Parkthemachineonalevelsurface,lowerthe

cuttingdecks,applytheparkingbrake,shutoff

theengineandremovethekey.

2.UsingthedimensionsshowninFigure1,locate,

markanddrill2holes(0.221or0.228inch,#1

or#2drillsize)inthetractionunitframetubefor

thenumber5liftarm.Drillthroughonly1wall

ofthetube.

Note:Useofa90°drillisrecommended.

g024884

Figure1

1.4.4cm(1.75Inches)3.4.1cm(1.63inches)

2.Holes(0.221or0.228

inch)

4.3.5cm(1.38inches)

3.Mounttherightdeck-lockmanifoldtotheframe

tubewith2selftappingscrews(1/4x1-3/4inch).

PositionthemanifoldasshowninFigure2.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3442-456*

Summary of content (4 pages)

PAGE 1
Form No. 3442-456 Rev A Deck Lock Kit Groundsmaster® 4500-D/4700-D Traction Unit Model No. 119-8641 Installation Instructions Installation This kit automatically prevents uneven settling of the mower decks. Note: Determine the left and right sides of the machine from the normal operating position. 1 Installing a Deck-Lock Manifold for the Number 1 Lift Arm Parts needed for this procedure: 1 Right manifold assembly (Part No.
PAGE 2
g024885 Figure 2 1. Straight hydraulic fitting g024887 Figure 4 3. 90-degree hydraulic fitting 1. New hose 2. Deck-lock manifold 4. Install the straight hydraulic fitting into the top of the manifold (Figure 2). 5. Install the 90-degree hydraulic fitting into the end of the manifold (Figure 2). 6. Place a drain pan under the junction manifold (Figure 3). 7. Disconnect the hydraulic hose from the lower center fitting on the junction manifold (Figure 3). 3. Deck-lock manifold top fitting 2.
PAGE 3
g024889 Figure 6 1. Straight hydraulic fitting 3. 90-degree hydraulic fitting 2. Deck-lock manifold 3. Install the straight hydraulic fitting into the top of the manifold (Figure 6). 4. Install the 90 degree hydraulic fitting into the end of the manifold (Figure 6). 5. Place a drain pan under the junction manifold (Figure 7). 6. Disconnect the hydraulic hose from the lower left fitting on the junction manifold (Figure 7). g024888 Figure 5 1. 4.4 cm (1.75 inches) 3. 4.1 cm (1.63 inches) 2.
PAGE 4
g024891 Figure 8 1. Disconnected hose 3. Deck-lock manifold top fitting g024892 Figure 9 (Groundsmaster 4700–D Machine Shown) 2. New hose 8. Route and install the new hose to the junction manifold and 90-degree, deck-lock manifold fitting (Figure 8). 1. Harness connectors 3. Plug the connector on the deck-lock harness labeled S5 SOLENOID to the S5 solenoid on the lift manifold (Figure 9). 4.