Installation Instructions

ManualsBrandsToro ManualsAttachmentsBeacon Kit, Groundsmaster 360 Series Multi-Purpose Machine

FormNo.3369-148RevA

BeaconKit

Groundsmaster

360SeriesMulti-PurposeMachine

ModelNo.120-0256

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Disconnectthenegativebatterycable

Decal,beacon1

Switch

Wireharness1

Installtheswitch

Beacon1

Beaconsocket1

Beaconmount,ROPS

U-bolt1

Locknut,3/8inch

Mountingpad3

Cabletie

InstallthebeacontotheROPS

Beacon1

Beaconsocket1

Beaconmount,cab1

Screw,3/8x7/8inch

Flangenut,3/8inch

Mountingpad3

Cabletie

Installthebeacontothecab

Nopartsrequired

–

Connectthenegativebatterycable

DisconnectingtheNegative

BatteryCable

NoPartsRequired

Procedure

1.Positionthemachineonalevelsurface,lowerthe

cuttingunits,stoptheengine,engagetheparking

brakeandremovethekeyfromtheignition.

CAUTION

Ifyouleavethekeyintheignitionswitch,

someonecouldaccidentlystarttheengineand

seriouslyinjureyouorotherbystanders.

Removethekeyfromtheignitionbeforeyoudo

anymaintenance.

2.Disconnectthenegativebatterycablefromthe

battery.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3369-148 Rev A Beacon Kit Groundsmaster® 360 Series Multi-Purpose Machine Model No. 120-0256 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Use Qty.
PAGE 2
8. Locate the wire harness connector labeled “Accessory”. Plug the wire harness connector into the connector. 2 Installing the Beacon Switch 9. Route the harness to the right ROPS tube or the right rear corner of the cab. Parts needed for this procedure: 10. Cable tie the harness away from any hot or rotating components and avoid any possible pinch points. 1 Decal, beacon 1 Switch 1 Wire harness 11. Install the control panel or access panel with the screws previously removed.
PAGE 3
2 1 3 1 4 5 6 7 G016454 Figure 3 1. 7-1/2 inches (19 cm) 3. Mount the beacon socket to the beacon mount with the jam nut included (Figure 2). G016453 Figure 2 1. 2. 3. 4. U-bolt Beacon Beacon socket Beacon mount 4. Plug the beacon onto the socket and tighten the wing nut (Figure 2). 5. Lock nuts 6. Mounting pad 7. Cable tie 5. Route the wire harness up the ROPS and plug it into the beacon socket. 6.
PAGE 4
2 1 Installing the Beacon (When equipped with a cab) 3 Parts needed for this procedure: 1 Beacon 1 Beacon socket 1 Beacon mount, cab 1 Screw, 3/8 x 7/8 inch 1 Flange nut, 3/8 inch 3 Mounting pad 3 Cable tie 4 5 6 7 Procedure 1. Secure the beacon mount (cab) to the tab on the right rear corner of the cab frame with a 3/8 x 7/8 inch screw and a 3/8 inch flange nut (Figure 4). Make sure the tab on the beacon mount is resting against the bottom of the cab frame tab. 2.