Installation Instructions

ManualsBrandsToro ManualsLawn TractorsToro 120-1190

FormNo.3368-455RevA

BeltGuardKit

DH200SeriesLawnTractor

ModelNo.120-1190

InstallationInstructions

Donotsupplytheseinstructionstothecustomer.

TheseinstructionsareforadealertoinstalladditionalbeltguardsmandatedbytheFrenchgovernment.

Safety

SafetyandInstructional

Decals

Safetydecalsandinstructionsareeasily

visibletotheoperatorandarelocated

nearanyareaofpotentialdanger.

Replaceanydecalthatisdamagedor

lost.

120-1119

1.Firehazard—readtheOperator’sManual.

Installation

PreparingforInstallation

NoPartsRequired

Procedure

Important:Refertothe

Operator’ s Man ual

ifyou

areunfamiliarwiththespecicsofoperatingthis

machinebeforeproceeding.Themanualcontains

importantinformationaboutsafelyoperatingthe

machine.Ifyoudonotknowthisinformation,you

couldseriouslyinjureyourselforothers.

1.Parkthemachineonalevel,smoothsurfacewith

sufcientspacetoaccessbothsidesofthemowing

deck.

2.Lowerthemowingdecktotheshortestcutting

height.

WARNING

Beforeworkingonthemachine,stoptheengine,

settheparkingbrake,removetheignitionkey,

anddisconnectthesparkplugwire.

CAUTION

Ifyouleavethekeyintheignitionswitch,

someonecouldaccidentlystarttheengineand

seriouslyinjureyouorotherbystanders.

Removethekeyfromtheignitionanddisconnect

thewirefromthesparkplugbeforeyoudoany

maintenance.Setthewireasidesothatitdoes

notaccidentallycontactthesparkplug.

3.Supporttherearaxleonbothsidesandremoveboth

rearwheels.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3368-455 Rev A Belt Guard Kit DH 200 Series Lawn Tractor Model No. 120-1190 Installation Instructions Do not supply these instructions to the customer. These instructions are for a dealer to install additional belt guards mandated by the French government. Safety Installation Safety and Instructional Decals 1 Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 120-1119 1.
PAGE 2
Installing the Deck Guard Parts needed for this procedure: 1 Deck belt guard 2 Bolt (M5 x 12) 2 Washer (M5.3) 2 Locknut (M5) Figure 2 1. Drill 5.5 mm diameter (2) 2. Measure dimensions 3 and 4 from the line between the center of the right bolt hole and the center of the spindle. 3. 16 mm Procedure 1. Remove the belt from the PTO clutch and the idler tension spring from the idler pulley (Figure 1). 4. 90 mm 5. 256 mm (2) 6. Measure dimension 5 from the centerline of the right bolt hole. 6.
PAGE 3
Installing the Left Belt Guard Parts needed for this procedure: 1 Left belt guard 1 Hex bolt (M8-1.25 x 12) 1 Washer (M8) 1 Locknut (NIM8-1.25) 2 Self-tapping screw (M4.2 x 13) Figure 5 Fasteners and attachment points for the left belt guard 1. Locknut (NIM8-1.25) 2. Washer (M8) Procedure 4. Locknut, existing (2) 5. Self-tapping screw (M4.2 x 13) (2) 3. Hex bolt (M8-1.25 x 12) 1. On the left side of the machine, drill 2 holes as specified in Figure 4.
PAGE 4
Installing the Right Belt Guard Figure 8 Measurements to drill hole in the rear footrest support Parts needed for this procedure: 1. 3.4 mm diameter 2. 11 mm 1 Right belt guard 1 Hex bolt (M8-1.25 x 12) 1 Washer (M8) 1 Locknut (NIM8-1.25) 5 Self-tapping screw (M4.2 x 13) 3. 50 mm C. Drill the holes in the front frame as specified in Figure 9. Procedure 1.