Installation Instructions

ManualsBrandsToro ManualsRiding ProductsHydraulic Hose Upgrade Kit, Rear Remote Hydraulics Kit Model 08781

FormNo.3373-854RevA

HydraulicHoseUpgradeKit

RearRemoteHydraulicsKitModel08781

ModelNo.120-3434

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removetheaircleaner.

Nopartsrequired

–

Removethehydraulicreservoirand

shrouds.

90-degreetee1

Hose1

Hydrauliccap1

Installthenewhydrauliccomponents.

Nopartsrequired

–

Installthehydraulictank.

Nopartsrequired

–

Tightenallconnections.

Nopartsrequired

–

Installthescreen,shrouds,andtire.

PreparingtheMachine

NoPartsRequired

Procedure

Thoroughlycleanthemachine.Removealldebrisfrom

themachinetoensurethatthenewcomponentswillt

properlyandthatnodirtordebrisentersthehydraulic

system.

RemovingtheAirCleaner

NoPartsRequired

Procedure

1.Thoroughlycleantheareaaroundtheair-cleaner

canister.

2.Loosentheradiatorclamparoundthehoseand

lowertheclampontothehose.

3.Removetheinsideboltthatholdstheaircleanerin

place.

Note:Retainthebolt.

4.Removetheair-cleanercoverandlter(Figure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3373-854 Rev A Hydraulic Hose Upgrade Kit Rear Remote Hydraulics Kit Model 08781 Model No. 120-3434 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 Description Use Qty. No parts required – Prepare the machine. No parts required – Remove the air cleaner.
PAGE 2
3 Removing the Hydraulic Reservoir and Shrouds No Parts Required Procedure 1. Drain the hydraulic tank; refer to the machine Operator's Manual. Figure 1 1. Air-cleaner canister 2. Air filter 2. Raise the rear of the machine off the ground and block up the rear of the machine. 3. Canister cover Note: Refer to Jacking the Machine in the Operator's Manual for your machine. 5. Remove the hose from the air-cleaner canister. 6.
PAGE 3
4 Installing the New Hydraulic Components 1 2 Parts needed for this procedure: 3 90-degree tee 1 Hose 1 Hydraulic cap Procedure G003836 1. Disconnect the short hydraulic line from the coupler fitting and the hydraulic-line port (Figure 6). Figure 4 1. Flange-head screw (2) 1 3. Left front screen 2. Frame 6. Disconnect the hydraulic lines going to the tank. 7. Remove the top hydraulic-tank bracket from the machine frame, and loosen the 2 brackets on the side of the frame. (Figure 5).
PAGE 4
6 2 Tightening All Connections 1 4 No Parts Required Procedure 5 Note: Ensure that the hoses and hydraulic lines are routed away from and to do not rub against any sharp, hot, or moving components. G018781 3 1. When you have installed all hydraulic lines and hoses, tighten all connections. Figure 7 1. Hose 2. Tee fitting 4. Small molded hose 5. Small hydraulic tube 2. Use a backup wrench on all tank fittings. 3. Hydraulic cap 7 5.