Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 120-7123

FormNo.3369-688RevA

48and54inchBaggerFinishingKit

2011andAfterTITANSeriesZero-Turn-RadiusRidingMower

ModelNo.120-7122

ModelNo.120-7123

InstallationInstructions

ThiskitrequirestheBaggerKit79326tocompleteinstallation.For

allTITANSeriesmowers,beginFinishingKitinstallationbefore

installingthebaggerkit.ContactyourAuthorizedServiceDealer

orToroCustomerServicetoobtainthenecessaryparts.Formore

information,visitusatwww.Toro.com.

Safety

Important:TheROPSrollbarisanintegraland

effectivesafetydevice.Keeptherollbarinthe

fullyraisedandlockedpositionwhenoperatingthe

mower.Lowertherollbartemporarilyonlywhen

absolutelynecessary.

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaof

potentialdanger.Replaceanydecalthatisdamagedorlost.

110-6691

1.Thrownobjecthazard—keepbystandersasafedistance

fromthemachine.

2.Thrownobjecthazard,mower—donotoperatewithoutthe

deector,dischargecover,orgrasscollectionsystemin

place.

3.Cutting/dismembermentofhandorfoot—stayawayfrom

movingparts.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3369-688 Rev A 48 and 54 inch Bagger Finishing Kit 2011 and After TITAN Series Zero-Turn-Radius Riding Mower Model No. 120-7122 Model No. 120-7123 Installation Instructions This kit requires the Bagger Kit 79326 to complete installation. For all TITAN Series mowers, begin Finishing Kit installation before installing the bagger kit. Contact your Authorized Service Dealer or Toro Customer Service to obtain the necessary parts. For more information, visit us at www.Toro.com.
PAGE 2
Installation 2 1 1 3 G010701 Installing the Weight 4 Parts needed for this procedure: Figure 2 2 Weight 2 Adhesive bumper 1 Rod 4 Washer 2 Hair pin 1. Cutaway of the front of the 3. Weight machine frame 2. Bumper 4. Rest the weight here during install Important: Whenever you remove the bagger attachment, remember to remove the front weight to return the proper stability to the machine. Procedure 1. Install an adhesive bumper to the weight (Figure 1). G016271 1 2 3 5 4 Figure 1 1.
PAGE 3
2 G016263 Installing the Bagger Frame Parts needed for this procedure: 1 Bagger frame (discard frame in bagger kit) 1 Bagger frame support bracket (discard bracket in bagger kit) 2 Self tapping screw (5/16 x 3/4 inch) (included in bagger kit) 4 Hair pin cotter — Included in Bagger Kit 79326 2 Rod — Included in Bagger Kit 79326 4 Washer — Included in Bagger Kit 79326 2 Bolt (5/16 x 2-1/2 inch) — Included in Bagger Kit 79326 2 Lock nut (5/16 inch) — Included in Bagger Kit 79326 1 Clevis pin
PAGE 4
6 3 4 4 3 5 Installing the Chute Parts needed for this procedure: 1 2 G010581 Figure 6 Left side shown 1. Bagger frame 2. Clevis end 3. Clevis pin 1 Straight baffle (48 inch decks only) 1 Curved baffle (54 in decks only) 1 Lock nut (5/16 inch) 1 Hand knob 1 Washer 1 Chute Procedure 4. Hair pin 5. Bracket on frame 6. Washer Use this procedure when installing the Finishing Kit on machines with both 48 and 54 inch decks. WARNING 7.
PAGE 5
2 4. Install the chute to the deck making sure the opening in top of the chute aligns with the exposed post on the deck top (Figure 9). 3 1 5 4 1 2 2 6 3 6 G010637 7 5 Figure 7 1. 2. 3. 4. Deflector assembly 5. Lock nut (existing) Fasteners (existing), retain 6. Forward hole 7. Front retaining clasp Carriage bolt (existing) Cut off baffle (existing) G010638 Figure 9 1. Discharge chute 2. Remove the deflector assembly and reinstall the cut off baffle.
PAGE 6
2. Lift the bagger top and install the bags by sliding the bag frame hooks onto the retaining brackets (Figure 12). 4 1 Installing the Bagger Top Parts needed for this procedure: 1 Circular cotter pin Procedure 1. Install the bagger top to the bagger frame. Slide the brackets over the posts in the bagger frame and install the circular cotter into the hole in the right hand post (Figure 11). Rotate the bagger top down to the operating position.
PAGE 7
5 6 Connecting with the Discharge Tube Installing the Blades Parts needed for this procedure: No Parts Required 3 Procedure Hi-Lift blade Procedure 1. Slide the curved end of the discharge tube into the opening in the bagger top (Figure 14). 1. Remove the existing mower blades installed on your deck. Refer to the Removing the Blades section in the Operator’s Manual for more information. 2 1 G010641 2. Install the Hi-Lift mower blades located in loose parts.
PAGE 8
Maintenance 2 3 1 Removing the Finishing Kit Whenever the bagger kit is removed, the finishing kit should be removed using the following procedure. Retain all parts for future installation. 5 CAUTION 4 2 Removing the bagger changes the weight distribution of the machine. Operating the machine with the front weights installed without the bagger may cause an unstable condition which could result in a loss of control.