Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 120-7126

FormNo.3368-669RevA

BaggerFinishingKit

2011andAfterTITANZX6000SeriesZero-Turn-RadiusRiding

Mower

ModelNo.120-7126

InstallationInstructions

ThiskitrequirestheBaggerKittocompletetheinstallation.Contact

anAuthorizedServiceDealerorCustomerServicetoobtainthe

necessaryparts.Formoreinformation,gotowww.Toro.com.

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaof

potentialdanger.Replaceanydecalthatisdamagedorlost.

110-6691

1.Thrownobjecthazard—keepbystandersasafedistance

fromthemachine.

2.Thrownobjecthazard,mower—donotoperatewithoutthe

deector,dischargecover,orgrasscollectionsystemin

place.

3.Cutting/dismembermentofhandorfoot—stayawayfrom

movingparts.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3368-669 Rev A Bagger Finishing Kit 2011 and After TITAN ZX6000 Series Zero-Turn-Radius Riding Mower Model No. 120-7126 Installation Instructions This kit requires the Bagger Kit to complete the installation. Contact an Authorized Service Dealer or Customer Service to obtain the necessary parts. For more information, go to www.Toro.com. Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger.
PAGE 2
Installation 1 Installing the Bagger Support and Bagger Frame Parts needed for this procedure: 1 Bagger support 1 Bagger frame assembly 1 Support spacer plate (from the Bagger Kit) 2 Self tapping screw (5/16 x 3/4 inch) (from the Bagger Kit) 2 Bolt (5/16 x 2-1/2 inch) (from the Bagger Kit) 2 Locknut (5/16 inch) (from the Bagger Kit) 1 Clevis pin (1/2 x 2-1/4 inch) (from the Bagger Kit) 5 Hair pin cotter (from the Bagger Kit) 2 Rod (from the Bagger Kit) 4 Washer (from the Bagger Kit) Fig
PAGE 3
10. Insert the bent ends of the rod into the machine frame as shown in Figure 4, and secure the end of the rod with a washer and a hair pin cotter. 11. Adjust the support rods so that the bagger frame is held secure to the machine frame and seats in the notch of the angle spacer plate installed previously. 12. Repeat these steps for each support rod: A. Loosen the jam nut at the base of the clevis end of the rod. B. Rotate the clevis end of the rod to adjust the rod to the desired length. C.
PAGE 4
3 2 1 G010632 Installing the Weight Parts needed for this procedure: 1 4 Weight 1 Adhesive bumper pad 1 Rod 4 Flat washer 2 Hair pin cotter 8 Spacer 6 3 5 Figure 6 1. Weight 2. Adhesive bumper pad 3. Spacers (8) 4. Rod 5. Hair pin cotter (2) 6. Washer (4) 3. Install the weight to the front of the machine frame (Figure 6). Procedure 4. Secure the weight with a rod, 8 spacers, 4 washers, and 2 hair pin cotters as shown in Figure 6.
PAGE 5
3 2 4 1 Installing the Chute 4 Parts needed for this procedure: 1 Angled cutoff baffle 1 Curved baffle 2 Locknut (5/16 inch) 1 Hand knob 1 Washer 1 Chute 5 G013095 Figure 8 1. Deflector assembly 2. Locknut (existing; retain) Procedure 4. Carriage bolt (existing; reuse) 5. Carriage bolt (existing; retain) 3. Locknut (existing, reuse) WARNING 2. Remove the deflector assembly.
PAGE 6
G013098 A. Align the vertical post in the curved baffle with center, forward hole in the deck and the horizontal post with the hole in the front wall of the mower deck. B. Secure horizontal post to the front wall of the deck using a locknut. 5. Install the chute to the deck. Note: Ensure that the opening in top of the chute aligns with the exposed post on the deck top and the forward vertical plate mates with the folded metal bracket of the chute (Figure 10). 2 1 Figure 11 1. Retaining clasp 1 2.
PAGE 7
Maintenance 2 1 G010641 Removing the Finishing Kit Whenever you remove the bagger kit, remove the finishing kit using the following procedure. Retain all parts for future installation. 1. Remove the discharge tube from the machine and install the discharge cover. 3 WARNING An uncovered discharge opening could allow the lawn mower to throw objects in the operator or bystander’s direction and result in serious injury. Also, contact with the blade could occur.
PAGE 8