Installation Instructions

ManualsBrandsToro ManualsAttachmentsHeavy-Duty DPA MVP Kit, 22-, 27- and 32-inch DPA Cutting Units for Reelmaster 3100 Series, 5010 Series, 6500/6700 Series and 7000 Series Traction Unit

FormNo.3369-257RevA

Heavy-DutyDPAMVPKit

22-,27-and32-inchDPACuttingUnitsforReelmaster3100Series,

5010Series,6500/6700Seriesand7000SeriesTractionUnit

ModelNo.120-7230

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Removetheoldbedbaradjusters

Shaftadjuster

Wavewasher2

Flangebushing4

Flatwasher2

Locknut2

Bedbaradjusterscrew2

Hardenedwasher2

Compressionspring

Springtensionnut

Installthenewbedbaradjusters

MediaandAdditionalParts

Description

Qty.

Use

Installationinstructions1Usetoinstallkit

Partscatalog1

Referencepartnumbers

RemovingtheOldBedbar

Adjusters

1.Parkthemachineonalevelsurface,lowerthecutting

units,applytheparkingbrake,switchofftheengine

andremovetheignitionkey.

2.Turnthebedbaradjustingscrews,counterclockwise,

tobackthebedknifeawayfromthereel(

Figure1).

Figure1

1.Bedbaradjustingscrew3.Bedbar

2.Springtensionnut

4.Washer

3.Backoutthespringtensionnut,untilthewasheris

nolongertensionedagainstthebedbar(

Figure1).

4.Removethespringtensionnut,compressionspring

andwasherfrombedbaradjusterscrew(Figure4).

5.Oneachsideofthemachine,loosenthelocknut

securingthebedbarbolt(Figure2).

Figure2

1.Bedbarbolt2.Locknut

6.Removeeachbedbarboltallowingbedbartobe

pulleddownwardandremovedfrommachinebolt

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3369-257 Rev A Heavy-Duty DPA MVP Kit 22-, 27- and 32-inch DPA Cutting Units for Reelmaster 3100 Series, 5010 Series, 6500/6700 Series and 7000 Series Traction Unit Model No. 120-7230 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty.
PAGE 2
(Figure 2). Account for 2 nylon and 1 stamped steel washers on each end of bedbar (Figure 3). 7. Unscrew bedbar adjuster shaft from the bedbar adjuster screw (Figure 4). The bedbar adjuster shaft has left-hand threads. 8. Remove the retaining ring and wave washer from the adjuster shaft and remove the adjuster shaft from the cutting unit frame (Figure 4). 9. Remove the flange bushings from the cutting unit center frame (Figure 4). 10. Repeat the procedure on the other end of the cutting unit. Figure 3 1.
PAGE 3
Installing the New Bedbar Adjusters 7. Loosely install the hardened washer, spring and spring tension nut onto adjuster screw. 8. Install the bedbar, positioning the mounting ears between washer and bedbar adjuster. 1. Thoroughly clean inside the casting area where the bushings were removed. 2. Apply Never Seize to the inside of the bushing area on cutting unit center frame (Figure 5). 3. Align the keys on flange bushings to the slots in the frame and install the bushings (Figure 5). 4.
PAGE 4