Installation Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 120-7770

FormNo.3368-779RevA

BeltGuardKit

TimeCutter

ZS3200RidingMower

ModelNo.120-7770

InstallationInstructions

Donotsupplytheseinstructionstothecustomer.

TheseinstructionsareforadealertoinstalladditionalbeltguardsonunitssoldinFrance.

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasily

visibletotheoperatorandarelocated

nearanyareaofpotentialdanger.

Replaceanydecalthatisdamagedor

lost.

110-6691

1.Thrownobjecthazard—keepbystandersasafedistance

fromthemachine.

2.Thrownobjecthazard,mower—donotoperatewithoutthe

deector,dischargecover,orgrasscollectionsystemin

place.

3.Cutting/dismembermentofhandorfoot—stayawayfrom

movingparts.

114-1606

1.Entanglementhazard,belt—keepallguardsinplace.

120-1119

1.Firehazard—readtheOperator’sManual.

Installation

PreparingforInstallation

NoPartsRequired

Procedure

Important:Refertothe

Operator’ s Man ual

ifyou

areunfamiliarwiththespecicsofoperatingthis

machinebeforeproceeding.Themanualcontains

importantinformationaboutsafelyoperatingthe

machine.Ifyoudonotknowthisinformation,you

couldseriouslyinjureyourselforothers.

1.Parkthemachineonalevel,smoothsurfacewith

sufcientspacetoaccessbothsidesofthemowing

deck.

WARNING

Beforeworkingonthemachine,stoptheengine,

settheparkingbrake,removetheignitionkey,

anddisconnectthesparkplugwire.

CAUTION

Ifyouleavethekeyintheignitionswitch,

someonecouldaccidentlystarttheengineand

seriouslyinjureyouorotherbystanders.

Removethekeyfromtheignitionanddisconnect

thewirefromthesparkplugbeforeyoudoany

maintenance.Setthewireasidesothatitdoes

notaccidentallycontactthesparkplug.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3368-779 Rev A Belt Guard Kit TimeCutter® ZS 3200 Riding Mower Model No. 120-7770 Installation Instructions Do not supply these instructions to the customer. These instructions are for a dealer to install additional belt guards on units sold in France. Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost.
PAGE 2
. Check the loose parts bag and verify that it contains all the parts listed in this document. 3 3. Remove the mowing deck and slide it out from under the traction unit; refer to the Operator’s Manual for this model. Installing the Deck Belt Guard Parts needed for this procedure: 2 Assembling the Deck Belt Guard Left deck guard plate 1 Right deck guard plate 1 Top deck guard plate 6 Hex Bolt (M6-1X16) 6 Locknut (NIM6-1) Hex bolt (M8-1.25X20) 1 Washer (M8) 1 Locknut (NIM8-1.
PAGE 3
Figure 4 1. Rear belt guard Figure 3 1. Washer (M8) 2. Locknut (NIM8-1.25) 3. Deck belt guard assembly 2. Hex bolts 3. Verify that the guard is clear of all moving parts across their full range of operation, that it will not cause damage to wires, hoses or other components and that it will not interfere with the safe operation of the traction unit. 4. Hex bolt (M8-1.25X20) 5. Deck 3.
PAGE 4