Installation Instructions

ManualsBrandsToro ManualsAttachmentsHigh Height-of-Cut Kit, Greensmaster DPA Reel Mowers

FormNo.3390-822RevA

HighHeight-of-CutKit

Greensmaster

DPAReelMowers

ModelNo.120-9600

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

1.Disengagethedrives,lowerthereels,settheparking

brake,andstoptheenginebeforeadjustingtherollers.

2.Loosenthescrewssecuringthefrontrollershafttothe

height-of-cutarms(Figure1).

3.Removethefrontroller(Figure1).

4.Removetheplowbolts,washersandnutssecuringthe

height-of-cutarmstothecuttingunitsideplate(Figure

1).

5.Removetheheight-of-cutarms.

6.Removetheadjustingscrewsfromtheheight-of-cut

arms(Figure1).

g017167

Figure1

1.Height-of-cutarm

3.Adjustingscrew

2.Plowbolt,washer,and

angenut

4.Screw

7.Applyananti-seizelubricanttothethreadsofthe

adjustingscrews.Threadthescrewsintothenew

height-of-cutarms.

8.Looselymounttheheight-of-cutarmstothecutting

unitsideplateswiththeplowbolts,washers,andnuts

previouslyremoved.

9.Installtherollerintotheheight-of-cutarms.

10.Centertherollerbetweentheheight-of-cutarms.

Installandtightenthenewscrewssecuringtheroller

shafttotheheight-of-cutarms.

11.Removethescrewsandnutssecuringtherearroller

bracketsandspacerstothesideplatemountinganges

(Figure2).Discardthescrewsandnuts.

g017200

Figure2

1.Spacers

3.Rearrollerbracket

2.Sideplatemountingange

Note:OlderFlex21cuttingunitsdonothaveaside

platemountingange(Figure2).Skipsteps11-14if

thekitisbeinginstalledonanoldermodelunitand

discardthespacers.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3390-822*A

Summary of content (2 pages)

PAGE 1
Form No. 3390-822 Rev A High Height-of-Cut Kit Greensmaster® DPA Reel Mowers Model No. 120-9600 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. 1. Disengage the drives, lower the reels, set the parking brake, and stop the engine before adjusting the rollers. 2. Loosen the screws securing the front roller shaft to the height-of-cut arms (Figure 1). 3.
PAGE 2
12. Use the chart below to determine the amount of spacers that need to be positioned below the side plate mounting flanges to attain the desired height-of-cut. Rear Roller Spacers Height-of-Cut (mm) Height-of-Cut (inches) 0 9.5 to 11.9 mm 0.375 to 0.469 inches 1 >11.9 to 14.3 mm 0.469 to 0.563 inches 2 >14.3 to 16.7 mm 0.563 to 0.656 inches 3 >16.7 to 19.1 mm 0.656 to 0.750 inches 4 >19.1 mm 0.750 inches 13.