Installation Instructions

ManualsBrandsToro ManualsAttachmentsController Replacement Kit, 2010-11 Pro Force Debris Blower

FormNo.3372-980RevA

ControllerReplacementKit

2010-11ProForceDebrisBlower

ModelNo.121-2812

InstallationInstructions

Installation

1.Disconnectthenegativebatterycablerstandthen

disconnectthepositivebatterycable.

2.Disconnectthewireharnessconnectorsfromthe

receiver(

Figure1).

g017839

Figure1

1.Receiver2.Wireharnessconnectors

3.Removethe(3)screwsandnutssecuringthereceiver

totheblowerframe(Figure1).Removethereceiver.

4.Positionthenewreceiverontotheframealigningit’s

rightmountingholewiththeupperrightmounting

holeusedtomounttheoldreceiver(

Figure2).

g018294

Figure2

1.Receiver

5.Usingtheleftholeinthenewreceiverasatemplate,

locate,markanddrilla.281inch(.713cm)diameter

holeintheframe(Figure2).Makesurethewireless

controllerislevel.

Note:Theholes,describedinsteps8and10,may

alsobedrilledatthistime,ifdesired.

6.Mountthenewreceivertothefrontoftheframe

with(2)1/4x1–1/4inchscrewsand1/4inchange

nuts(

Figure3).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3372-980 Rev A Controller Replacement Kit 2010-11 Pro Force Debris Blower Model No. 121-2812 Installation Instructions Installation 1. Disconnect the negative battery cable first and then disconnect the positive battery cable. 2. Disconnect the wire harness connectors from the receiver (Figure 1). 1 1 2 g018294 Figure 2 1. Receiver g017839 Figure 1 1. Receiver 2. Wire harness connectors 3. Remove the (3) screws and nuts securing the receiver to the blower frame (Figure 1).
PAGE 2
3 2 3 2 1 1 g018296 g018298 Figure 3 1. Screw, 1/2 x 1–1/4 inch Figure 5 3. Flange nut, 1/4 inch 1. Carriage screw, 1/4 x 5/8 inch 2. Transmitter mount 2. Receiver 7. Disconnect the remainder of the wire harness connections and remove the harness from the machine. 10. Using the dimensions shown in Figure 6, locate mark and drill (4) .281 inch (.713 cm) diameter holes in the frame. 8. Using the dimensions shown in Figure 4, locate, mark and drill (2) .281 inch (.
PAGE 3
Operation Controls 3 Engine Stop Press the Engine Stop button to stop the engine (Figure 8). 2 1 g018300 1 2 3 4 5 6 Figure 7 1. Relay (4) 3. Flange nut, 1/4 inch 2. Screw, 1/4 x 3/4 inch 12. Route, secure and connect the new wire harness to the machine. 13. Store the new transmitter on the transmitter mount when it is not in use. 14. Connect the positive battery cable first and then connect the negative battery cable. g017705 Figure 8 15. The handheld and base unit should be associated.
PAGE 4
Starting and Stopping the Engine 4. Engine Start will only become energized by pressing the Start button while the Engine Start Enable Condition is active. The Engine Start Enable Condition becomes active only when the following Engine Start Enable Sequence has been performed (Figure 10). Starting the Engine WARNING • Press the START button. ROTATING PARTS CAN CAUSE SERIOUS PERSONAL INJURY • Then, press the rotate left button. • Then, press the rotate right button.
PAGE 5
1 2 3 4 5 6 LEDs indicate that the remote control is alive and communicating with the base unit. To conserve battery power, the remote control stays active for approximately three (3) seconds before automatically shutting down unless there is button activity within the three second limit. When the unit times out and powers down, all remote control LED activity stops (Figure 11). Pressing any button will reactivate the remote control. 3 4 5 g017705 Figure 10 1. Rotate nozzle left 4.
PAGE 6
Maintenance Adjusting the Nozzle Direction The direction of the nozzle opening can be changed from right to left by pressing the appropriate button on the remote control (Figure 12). Associate Remote Control and Base Unit Important: Make sure to read the entire procedure before attempting the Association process. 1 The remote control must establish communications with the base unit before the system can be used. The remote control is associated to the system base unit before leaving the factory.
PAGE 7
which time TX begins flashing Green indicating that the remote control is transmitting. 3. If replacing expired batteries, remove the old batteries and install three fresh size AAA batteries. Be sure to position the batteries as shown in Figure 14. 8. Release the Associate button. RX extinguishes and TX flashes Green for a brief time and then it too goes out. 4. Replace the compartment cover and tighten the four Phillips screws.
PAGE 8
Schematics G018347 Electrical Schematic (Rev.