Installation Instructions

ManualsBrandsToro ManualsAttachmentsController Replacement Kit, 2008-09 Pro Force Debris Blower

FormNo.3373-363RevA

ControllerReplacementKit

2008-09ProForceDebrisBlower

ModelNo.121-2813

InstallationInstructions

Installation

1.Disconnectthenegativebatterycablerstandthen

disconnectthepositivebatterycable.

2.Disconnectthewireharnessconnectorsfromthe

receiver(Figure1).

g017839

Figure1

1.Receiver2.Wireharnessconnectors

3.Removethe(3)screwsandnutssecuringthereceiver

totheblowerframe(Figure1).Removethereceiver.

4.UsingthedimensionsshowninFigure2,locate,

markanddrill(2).281inch(.7cm)diameterholes

intheframe.

4.038 in

10.3 cm

.836 in

2.1 cm

4.415 in

11.2 cm

G018388

Figure2

Note:Theholes,describedinsteps6and8,may

alsobedrilledatthistime,ifdesired.

5.Mountthenewreceivertothebackoftheframe

with(2)1/4x1–1/4inchscrewsand1/4inchange

nuts(

Figure3).

G018432

Figure3

1.Flangenut,1/4inch3.Screw,1/2x1–1/4inch

2.Receiver

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3373-363 Rev A Controller Replacement Kit 2008-09 Pro Force Debris Blower Model No. 121-2813 Installation Instructions Installation 1. Disconnect the negative battery cable first and then disconnect the positive battery cable. 2. Disconnect the wire harness connectors from the receiver (Figure 1). 4. Using the dimensions shown in Figure 2, locate, mark and drill (2) .281 inch (.7 cm) diameter holes in the frame. 4.038 in 10.3 cm .836 in 2.1 cm 1 2 4.415 in 11.
PAGE 2
6. Using the dimensions shown in Figure 4, locate, mark and drill (2) .281 inch (.7 cm) diameter holes in the side of the frame (Figure 4). .980 in 2.5 cm 8. Using the dimensions shown in Figure 6, locate mark and drill (3) .281 inch (.7 cm) diameter holes in the frame. 1.500 in 3.8 cm 11.495 in 29.2 cm 12.495 in 31.7 cm 2.125 in 5.4 cm G018434 Figure 4 7. Install the transmitter mount to the side of the frame with a 1/4 x 5/8 inch carriage screw and a 1/4 inch flange nut (Figure 5).
PAGE 3
Operation 10. Connect the new wire harness to the relays, existing wire harness and to the new receiver (Figure 8). Controls Engine Stop Press the Engine Stop button to stop the engine (Figure 9). 1 1 2 3 4 5 6 G018433 Figure 8 1. New wire harness 11. Store the new transmitter on the transmitter mount when it is not in use. g017705 Figure 9 12. Connect the positive battery cable first and then connect the negative battery cable. 1. Rotate nozzle left 4. Increase blower output 2.
PAGE 4
Starting and Stopping the Engine 4. Engine Start will only become energized by pressing the Start button while the Engine Start Enable Condition is active. The Engine Start Enable Condition becomes active only when the following Engine Start Enable Sequence has been performed (Figure 11). Starting the Engine WARNING • Press the START button. ROTATING PARTS CAN CAUSE SERIOUS PERSONAL INJURY • Keep hands and feet away from the machine when it is running.
PAGE 5
1 2 3 4 5 6 LEDs indicate that the remote control is alive and communicating with the base unit. To conserve battery power, the remote control stays active for approximately 3 seconds before automatically shutting down unless there is button activity within the three second limit. When the unit times out and powers down, all remote control LED activity stops (Figure 12). Pressing any button will reactivate the remote control. 3 4 5 g017705 Figure 11 1. Rotate nozzle left 4.
PAGE 6
Maintenance Adjusting the Nozzle Direction The direction of the nozzle opening can be changed from right to left by pressing the appropriate button on the remote control (Figure 13). Associate Remote Control and Base Unit Important: Make sure to read the entire procedure before attempting the Association process. 1 The remote control must establish communications with the base unit before the system can be used. The remote control is associated to the system base unit before leaving the factory.
PAGE 7
which time TX begins flashing Green indicating that the remote control is transmitting. 3. If replacing expired batteries, remove the old batteries and install three fresh size AAA batteries. Be sure to position the batteries as shown in Figure 15. 8. Release the Associate button. RX extinguishes and TX flashes Green for a brief time and then it too goes out. 4. Replace the compartment cover and tighten the four Phillips screws.
PAGE 8