Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 121-5662

FormNo.3372-308RevA

48,54,and60InchBaggerFinishingKit

TITANZX/MXSeriesRidingMower

ModelNo.121-5662

ModelNo.121-5663

ModelNo.121-5664

InstallationInstructions

ThiskitrequirestheBaggerKit79328to

completeinstallation.ContactyourAuthorized

ServiceDealerorToroCustomerService

toobtainthenecessaryparts.Formore

information,visitusatwww.Toro.com.

Safety

Important:TheROPSrollbarisanintegralandeffectivesafetydevice.Keeptherollbarinthefullyraisedand

lockedpositionwhenoperatingthemower.Lowertherollbartemporarilyonlywhenabsolutelynecessary.

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential

danger.Replaceanydecalthatisdamagedorlost.

110-6691

1.Thrownobjecthazard—keepbystandersasafedistance

fromthemachine.

2.Thrownobjecthazard,mower—donotoperatewithoutthe

deector,dischargecover,orgrasscollectionsystemin

place.

3.Cutting/dismembermentofhandorfoot—stayawayfrom

movingparts.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (12 pages)

PAGE 1
Form No. 3372-308 Rev A 48, 54, and 60 Inch Bagger Finishing Kit TITAN ZX/MX Series Riding Mower Model No. 121-5662 Model No. 121-5663 Model No. 121-5664 Installation Instructions This kit requires the Bagger Kit 79328 to complete installation. Contact your Authorized Service Dealer or Toro Customer Service to obtain the necessary parts. For more information, visit us at www.Toro.com. Safety Important: The ROPS roll bar is an integral and effective safety device.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Use Qty. Weight Adhesive bumper Rod Washer Hair pin Spacer Straight baffle (48 inch mower decks only) Curved baffle (54 inch mower decks only) Lock nut (5/16 inch) Hand knob Washer Chute Curved baffle Lock nut (5/16 inch) Hand knob Washer Chute 2 2 1 4 2 8 Circular cotter pin 1 Install the bagger top. No parts required – Connect with the discharge tube.
PAGE 3
1 2 6 5 4 G01821 1 Figure 3 Installation of 1 weight Figure 1 1. Nut 3 3. Mower housing pan 2. Bolt 1. Adhesive bumper 4. Hair pin 2. Front weight 5. Washer 3. Rod 6. Spacers (used for one weight only) 3. Install an adhesive bumper to the weight (Figure 2 and Figure 3). 4. Install the weight to the front of the machine frame. G016271 1 2 5. Secure the weight with a rod, four washers, and two hair pins as shown in Figure 2.
PAGE 4
2 2 3 1 Installing the Chute for 48 and 54 inch Mower Decks 5 4 Parts needed for this procedure: 1 Straight baffle (48 inch mower decks only) 1 Curved baffle (54 inch mower decks only) 1 Lock nut (5/16 inch) 1 Hand knob 1 Washer 1 Chute 2 6 G010637 7 Figure 5 1. Deflector assembly Procedure 5. Lock nut (existing) 2. Fasteners (existing), retain 6. Forward hole Use this procedure when installing the Finishing Kit on machines with 48 and 54 inch mower decks. 3.
PAGE 5
G015685 7 1 2 6 Figure 8 1. Flexible latch and retaining clasp 3 5 4 3 Figure 6 1. Retaining clasp 5. Horizontal post 2. Forward hole 3. Baffle (curved shown) 6. Lock nut 7. Front wall hole Installing the Chute for 60 inch Mower Decks (Model Year 2010 and Newer) 4. Vertical post 5. Install the chute to the mower deck making sure the opening in top of the chute aligns with the exposed post on the mower deck top (Figure 7).
PAGE 6
3 2 4. Install the curved baffle to the mower deck (Figure 10). 1 A. Align the vertical post in the curved baffle with center, forward hole in the mower deck and the horizontal post with the hole in the front wall of the mower deck. B. Secure horizontal post to the front wall of the mower deck using a locknut. 4 5. Install the chute to the mower deck.
PAGE 7
G013098 2 1 Figure 12 1. Retaining clasp 2. Flexible latch 4 Installing the Bagger Top Parts needed for this procedure: 1 G016265 Figure 13 Circular cotter pin Procedure 1. Bagger top 4. Circular cotter pin 2. Bagger frame 5. Post 3. Bracket, bagger top 1. Install the bagger top to the bagger frame. Slide the brackets over the posts in the bagger frame and install the circular cotter into the hole in the right hand post (Figure 13). Rotate the bagger top down to the operating position.
PAGE 8
2. Lift the bagger top and install the bags by sliding the bag frame hooks onto the retaining brackets (Figure 14). 5 1 Connecting with the Discharge Tube No Parts Required Procedure 1. Slide the curved end of the discharge tube into the opening in the bagger top (Figure 16). 2 1 G010641 2 4 3 3 G005672 5 Figure 14 1. Bag 3. Retaining bracket 2. Bagger frame 4. Bag frame hook 4 3. Lower the bagger top onto the bag (Figure 15). Figure 16 1. Discharge tube, curved end 2.
PAGE 9
Maintenance 6 Removing the Finishing Kit Installing the Blades Whenever the bagger kit is removed, the finishing kit should be removed using the following procedure. Retain all parts for future installation. Parts needed for this procedure: 3 CAUTION Hi-Lift blade Removing the bagger changes the weight distribution of the machine. Operating the machine with the front weights installed without the bagger may cause an unstable condition which could result in a loss of control. Procedure 1.
PAGE 10
2 Blades section in the Operator's Manual for more information. 3 1 • Install the standard mower blades removed 5 previously. Refer to the Installing the Blades section in the Operator's Manual for more information. 4 Important: The ROPS roll bar is an integral and effective safety device. Keep the roll bar in the fully raised and locked position when operating the mower. Lower the roll bar temporarily only when absolutely necessary. 2 6 G010637 7 Figure 17 48 and 52 inch Mower Deck 1.
PAGE 11
Notes: 11
PAGE 12