Installation Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 121-5747

FormNo.3372-992RevA

DeckHangerKit

2011andBeforeTITANZero-Turn-RadiusRidingMower

ModelNo.121-5747

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Flangebushing2

Metalgusset2

Installtherearangebushings.

Flangebushing2

Metalgusset2

Installthefrontangebushings.

InstallingtheRearFlange

Bushings

Partsneededforthisprocedure:

2Flangebushing

2Metalgusset

Procedure

1.Place2blocks(2x4)undereachsideofthemower

deckandlowerthedeckdownontotheboards.

2.Removethe4hairpincottersandwashersfromthe

deckhangerliftlinksandremovethelinksfromthe

mowerdeck(Figure1).

g018039

Figure1

1.Hairpincotters,washersanddeckhangerliftlinks

3.Removethetwonutsandboltsateachexistingange

bushing(Figure2).

4.Turnbothangebushingssothattheopenendsare

facingdownward.

5.Pulltherearpivotbardown.

6.Removebothexistingangebushings.

7.Startingontherightside,installanewangebushing

betweenthestopandtheendofthebar.

8.Rotatetheangebushingsothattheopenendisfacing

upward.

9.Slidetheassemblyintoframe.

10.Installametalgussetontotheangebushingand

looselyinstalltheexistingnutsandbolts.

11.Ontheleftside,installanewangebushingintothe

frame,sothattheopenendoftheangebushingis

facingdownward.

12.Installthepivotrodintotheopenendoftheange

bushing.

13.Rotatetheangebushingsothattheopeningisfacing

upward.

14.Installametalgussetontotheangebushingand

installtheexistingnutsandbolts.

15.Tightenallfasteners.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (2 pages)

PAGE 1
Form No. 3372-992 Rev A Deck Hanger Kit 2011 and Before TITAN Zero-Turn-Radius Riding Mower Model No. 121-5747 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Flange bushing Metal gusset Flange bushing Metal gusset 1 2 Use Qty. 2 2 2 2 Install the rear flange bushings. Install the front flange bushings. 3. Remove the two nuts and bolts at each existing flange bushing (Figure 2). 1 4.
PAGE 2
3. Remove the existing flange bushings. 4. Install the new flange bushings onto the front pivot bar. 5. Install the front pivot bar with the new flange bushings into the frame. 6. Secure the flange bushings and metal gussets to the frame with the previously removed nuts and bolts (Figure 3). 1 5 1 7 6 2 6 4 5 3 g018067 1 Figure 2 1. Existing bolts 5. Flange bushing 2. New metal gusset, installed 3. Existing nuts 6. Rear pivot bar 7. Stop welded on rear pivot bar 3 4 4.