Installation Instructions

ManualsBrandsToro ManualsAttachmentsPivot Service Kit, Model 08751 Tooth Rake for Sand Pro Traction Unit

FormNo.3374-373RevA

PivotServiceKit

Model08751ToothRakeforSandPro

TractionUnit

ModelNo.121-9064

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Removetheexistingbracket.

Thrustwashers2

Clevispin

Pivottube1

Hitchassembly1

Jamnut(1/2inch)

Carriagebolt(1/2inch)

Cotterpin

Assemblethepivotbracket.

Screw(1/2inch)

Flangenut(1/2inch)

Locknut(1/2inch)

Screw(3/8inch)

Flangenut(3/8inch)

Installthepivotbrackettothemachine.

Rakestopplates2

Screw(1/2inch)

Clevispin

Cotterpin

Flatwashers2

Pivotbracketassembly1

Locknut(1/2inch)

Installthepivotbrackettotheattachment.

Nopartsrequired

–

Adjustthetineengagement.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3374-373*A

Summary of content (4 pages)

PAGE 1
Form No. 3374-373 Rev A Pivot Service Kit Model 08751 Tooth Rake for Sand Pro® Traction Unit Model No. 121-9064 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Description Qty.
PAGE 2
Removing the Existing Bracket Assembling the Pivot Bracket 1. Remove and discard the cotter and clevis pins securing the existing bracket and lower end of the latch mechanism (Figure 1). 2 3 1 4 g019966 5 Figure 1 6 7 g019957 Figure 3 2. Remove and discard the fasteners securing the bracket to the attachment (Figure 2). Discard the bracket. 1 1. Thrust washer 5. Hitch assembly 2. Clevis pin 6. Cotter pin 3. Carriage bolt (1/2 inch) 7. Pivot tube 4. Jam nut (1/2 inch) 2 1.
PAGE 3
Installing the Pivot Bracket to the Machine 5. Install a screw (3/8 inch) into the newly drilled hole and secure the bracket assembly with a flange nut (3/8 inch) (Figure 7). 1. Install the pivot bracket assembly to the frame with a screw (1/2 inch) and secure with a flange nut (1/2 inch) (Figure 5). 1 2 3 g019960 Figure 7 6. Torque the nut to 21–27 Nm (16-20 ft-lb). 4 5 Installing the Pivot Bracket to the Attachment g019964 Figure 5 1. Screw (1/2 inch) 4. Flange Nut (1/2 inch) 2.
PAGE 4
Adjusting the Tine Engagement 1 1 3 2 4 2 5 g019962 Figure 9 g019963 1. Washer 3. Right hand rake stop plate 2. Cotter pin 4. Clevis pin 4 3 Figure 11 4. Install the screw (1/2 inch) into the hole that provides the tine engagement desired. Refer to Adjusting the Tine Engagement (page 04). Note: The pivot bracket assembly needs to be removed and reinstalled to obtain specific levels of tine engagement. 1 5 g019963 3 1. Locknut (1/2inch) 4. Top hole 5. Screw (1/2 inch) 2. Top hole 5.