Installation Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 125-9310

FormNo.3381-168RevB

BafeKit

60inor72inRearDischargeZMaster

Mowers

ModelNo.125-9305

ModelNo.125-9310

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

RemovingtheOriginal

Hardware

NoPartsRequired

Procedure

1.Ensurethatallmovingpartshavestopped,theparking

brakeisengaged,andthekeyhasbeenremoved.

2.Raisethefrontofthemachineandsupportitwithjack

stands.

WARNING

Raisingthemowerdeckforserviceor

maintenancerelyingsolelyonmechanical

orhydraulicjackscouldbedangerous.The

mechanicalorhydraulicjacksmaynotbe

enoughsupportormaymalfunction,allowing

theunittofall,whichcouldcauseinjury.

Donotrelysolelyonmechanicalorhydraulic

jacksforsupport.Useadequatejackstands

orequivalentsupport.

Important:Theright-handbladeonthismower

deckiscounter-rotatingandusesaleft-hand

threadedbladebolt.

3.Removethebladesandretainthemforremovalofthe

bafekit.

4.Ifthemowerhasbeenused,scrapetheundersideof

themowerdeckclean.

5.Removethehardwarethatplugstheexposedmounting

holesinthedeck.

•For60-inchdecks,removethe6hex-socketscrews

(5/16-18x3/4inch)andangednylocnuts

pluggingtheexposedmountingholesinthedeck

(

Figure1).

Note:Retainthesepartsforfutureuse.

Figure1

60-inchdeckshown

1.Partsthatneedtoberetained

•For72-inchdecks,removethe4hex-socketscrews

(5/16-18x3/4inch),theangednutsplugging

theexposedmountingholesinthedeck,andthe

inboard-tire-apfasteneroneachside(

Figure2).

Note:Retainthesepartsforfutureuse.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3381-168*B

Summary of content (8 pages)

PAGE 1
Form No. 3381-168 Rev B Baffle Kit 60in or 72 in Rear Discharge Z Master® Mowers Model No. 125-9305 Model No. 125-9310 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. 5. Remove the hardware that plugs the exposed mounting holes in the deck.
PAGE 2
Installing the Baffles Parts needed for this procedure: Figure 2 72-inch deck shown 1. Socket screw 2. Carriage bolt 6. Remove and retain the 2 rear carriage bolts (3/8-16 x 2-1/4 inches) and flange nuts from each side within the cutting chamber that attach the side bumpers to the deck sides.
PAGE 3
Figure 3 1. Front right-hand baffle 8. Left-hand kicker baffle 2. Carriage bolt 9. Rear left-hand baffle 3. Flange nut 10. Locknut 4. Center kicker baffle 5. Front center baffle 11. Rear center baffle 12. Rear right-hand baffle 6. Front left-hand baffle 13. Right-hand kicker baffle 7. Carriage bolt (5/16-18 x 1 inch) and flange nut (5/16-18)—72-inch model only the innermost square hole on the inboard tire flap on each side (Figure 3). 1.
PAGE 4
3 Securing the Bumpers and the Right and Left-hand Baffle to the Mower Deck Parts needed for this procedure: Figure 4 1. Carriage bolt (3/8-16 x 7/8 inch) 3. Front baffle flange 2. Rear center baffle 4. Locknut (3/8-16) 4 Carriage bolt (3/8-16 x 2.5 inches) 4 Flange nut (3/8-16) Procedure Note: You may need to loosen the mating baffle and kicker baffle to allow the bumper bolts to be installed. 5. Tighten all of the hardware. 1. Insert 2 carriage bolts (3/8-16 x 2.
PAGE 5
4 Installing the Blades Parts needed for this procedure: 1 20.5-inch rotary blade (red)—60-inch model only 2 20.5-inch low-flow blade (black)—60-inch model only 1 24.5-inch rotary blade (red)—72-inch model only 2 24.5-inch low-flow blade (black)—72-inch model only Procedure Note: Determine the left and right sides of the machine from the normal operating position.
PAGE 6
5 Converting Back to Rear Discharge No Parts Required Procedure 1. Stop engine and wait for all moving parts to stop, engage the parking brake, remove the key, and disconnect the negative battery cable. 2. Remove the finish-cut baffles and the kicker baffles, and retain all of the hardware. 3. Replace the finish-cut blades with standard blades. 4. Install the 5/16-18 x 3/4-inch hex-socket screws and the flange nuts in the holes on top of the deck with the bolt head underneath.
PAGE 7
Notes: 7
PAGE 8