Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 126-9360

FormNo.3413-588RevA

CEKit

122cmand132cmE-ZVac

™

BaggerforTitan

HDRidingMower

ModelNo.126-9360

ModelNo.126-9361

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Note:TocreateaCEbagger,installthiskitontheBlowerandDriveKit(ToroModelNo.78483,78486,78433,or78436

for122cmmowerdecksorToroModelNo.78484,78487,78434,or78437for132cmmowerdecks),andwiththeE-Z

Vac™TwinBaggerKit(ToroModelNo.78481or78431).

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removethedischargechute.

Nopartsrequired

–

RemovetheOEMcoverandbracket.

Left,rearsupportrod

Right,rearsupportrod1

Whiznut(3/8inch)

Installtherearsupportrods(Bagger

Model78481only).

Nopartsrequired

–

Removetheblowerkitparts.

CEpulleyguard

CEbelt-coverbracket

Hex-headbolt(1/4x1inch)

Carriagebolt(1/4x3/4inch)

Flangenut(1/4inch)

Hex-headbolt(3/8x1inch)

Flangenut(3/8inch)

Clipnut

Rearguard(122cmmowerdeckonly)

InstalltheCEdeckbracket.

CEshaftguard

CEforwardguard

CEtensionerguard

InstalltheupperCEguards.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3413-588*A

Summary of content (12 pages)

PAGE 1
Form No. 3413-588 Rev A CE Kit 122cm and 132cm E-Z Vac™ Bagger for Titan® HD Riding Mower Model No. 126-9360 Model No. 126-9361 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Note: To create a CE bagger, install this kit on the Blower and Drive Kit (Toro Model No. 78483, 78486, 78433, or 78436 for 122 cm mower decks or Toro Model No.
PAGE 2
Procedure 8 9 Description Qty. 1 2 2 2 1 1 1 1 CE lower guard Hex-head bolt (1/4 x 3/4 inch) Washer (1/4 x 5/8) Locknut (1/4 inch) Hex-head bolt (1/4 x 3/4 inch) Washer (5/16 x 3/4 inch) Washer (1/4 x 1/2 inch) Retainer 2 Use Install the lower CE Guard. Install the CE belt cover.
PAGE 3
2. Remove the side discharge chute from the mower deck (Figure 1). 1 Note: Retain the chute and hardware for installation when operating the mower with the blower accessory removed. Preparing the Machine No Parts Required 3 Procedure 1. 2. 3. 4. Park the machine on a level surface. Engage the parking brake. Shut off the engine and remove the key. Thoroughly clean the mower deck.
PAGE 4
Removing the Cover Mounting Bracket 4 1. Remove the 2 bolts and 2 flange nuts that secure the cover mounting bracket to the deck (Figure 2). 2. Remove the bracket. Installing the Rear Support Rods (Bagger Model 78481 Only) Note: Retain the OEM cover mounting bracket, bolts, and flange nut for installation when operating the mower with the blower accessory removed.
PAGE 5
Removing the Belt Cover Bracket If the blower kit is installed on the machine, remove the belt cover bracket installed from the blower and drive kit as follows: 1. Remove the 2 carriage bolts (1/4 x 3/4 inch) and 2 locknuts (1/4 inch) that secures the belt-cover bracket to the forward flange of the mower deck (Figure 8). g203736 Figure 6 Left Side Shown 1. New rear support rod 2. Whiz nut (3/8 inch) 5 Removing the Blower Kit Parts (If Installed) g022380 Figure 8 No Parts Required 1.
PAGE 6
Removing the OEM Shaft Cover and Hardware Removing the OEM Shaft Cover and Hardware For Standard Blowers For HD Blowers 1. Remove the 2 nuts and 2 washers that secure the OEM shaft cover to the blower assembly (Figure 10). 1. Remove the 3 serrated nuts that secure the OEM shaft cover to the blower assembly (Figure 9). Note: Do not loosen the bolts and nuts that secure the upper-bearing housing that are beneath the OEM shaft cover.
PAGE 7
6 Installing the CE Pulley Guard and Belt-Cover Bracket Parts needed for this procedure: 1 CE pulley guard 1 CE belt-cover bracket 1 Hex-head bolt (1/4 x 1 inch) 1 Carriage bolt (1/4 x 3/4 inch) 2 Flange nut (1/4 inch) 2 Hex-head bolt (3/8 x 1 inch) 2 Flange nut (3/8 inch) 1 Clip nut 1 Rear guard (122 cm mower deck only) g203671 Figure 11 Installing the CE Pulley Guard and Belt-Cover Bracket 1. Hex-head bolt (3/8 x 1 inch) 6. Flange nut (1/4 inch) 2. Flange nut (3/8 inch) 7.
PAGE 8
Installing the CE Pulley Guard and Belt-Cover Bracket 7 For 132 cm Mower Decks Installing the CE Upper Guards 1. Align the holes of the CE pulley guard to the hole in the forward deflector bracket and the outboard hole in the forward deck flange (Figure 12). Parts needed for this procedure: Note: The CE pulley bracket wraps around the outboard edge of the deflector bracket 1 CE shaft guard 1 CE forward guard 1 CE tensioner guard Installing the CE Shaft Guard For Standard Blowers 1.
PAGE 9
Installing the CE Shaft Guard 8 For HD Blowers Install the CE shaft guard to the blower assembly using 2 nuts and 2 washers (Figure 14). Installing the CE Lower Guard Parts needed for this procedure: 1 CE lower guard 2 Hex-head bolt (1/4 x 3/4 inch) 2 Washer (1/4 x 5/8) 2 Locknut (1/4 inch) Removing the Blower If installed remove the blower assembly from the mower deck as follows: 1.
PAGE 10
Drilling the Mounting Holes for the CE Lower Guard 2. Move the idler pivot bracket toward the fixed spring post. remove the hook of the spring from the idler spring post (Figure 15). 1. Align the lower CE lower guard to the blower-chute bracket as shown in Figure 17. 3. Route the belt beneath the idler pulley (Figure 16). 4 1 5 6 7 3 1 2 2 10 10 3 7 4 5 8 9 9 11 G018859 g018859 Figure 17 6 G018367 5. Blower (housing repositioned for illustrative purposes) 2. Blower belt 6.
PAGE 11
Installing the CE Lower Guard Note: Install the CE lower guard with the blower assembly removed from the mower deck; refer to the E-Z Vac™ Blower and Drive Kit Installation Instructions. 1. Align the CE lower guard to the blower-chute bracket (Figure 17). 2. Align hole 2 and hole 4 of the CE lower guard to the rivet tails protruding through the blower-chute bracket(Figure 17). 3.
PAGE 12
2. Insert the bolt and washer through the hole in the top of the belt cover from the OEM blower and drive kit (Figure 18). 9 3. From the bottom of the belt cover, assemble the washer (1/4 x 1/2 inch) and retainer over the hex-head bolt threads (Figure 18). Installing the CE Belt Cover Ensure that the bolt head and washer are positioned flush with the upper surface of the belt cover and the washer and retainer are flush with the bottom surface of the cover.