Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 127-0336

FormNo.3394-377RevA

CEBaggerComplianceKit

for48in,52in,or60inZMaster

G3Mower

ModelNo.127-0336

ModelNo.127-0337

ModelNo.127-0338

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Note:Thiskitneedstobeinstalledonmodel78551,78552,78553,78562,78563,78566,or78567BlowerandDrive

KittocreateaCEbagger.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemower.

Warningdecal1

Covermissingdecal

Installthedecals.

Blowercover1

Bolt(1/4x3/4inch)

Washer(1/4inch)

Washer(5/16inch)

Plasticplug1

Pushnut(1/4inch)

Installthecovers.

Leftguard

Backguard1

Frontguard1

Lowerguard1

Bolt(5/16x3/4inch)

Flangenut(5/16inch)

Installtheguards.

Supportrod

1Installthesupportrod.

Muferguard

Installthemuferguard.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3394-377*A

Summary of content (8 pages)

PAGE 1
Form No. 3394-377 Rev A CE Bagger Compliance Kit for 48in, 52in, or 60in Z Master® G3 Mower Model No. 127-0336 Model No. 127-0337 Model No. 127-0338 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Note: This kit needs to be installed on model 78551, 78552, 78553, 78562, 78563, 78566, or 78567 Blower and Drive Kit to create a CE bagger. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
1 3 Preparing the Mower Installing the Covers No Parts Required Parts needed for this procedure: 1 Blower cover 1 Bolt (1/4 x 3/4 inch) 1. Thoroughly clean mower deck. All debris must be removed to ensure the kit will fit properly. 1 Washer (1/4 inch) 1 Washer (5/16 inch) 2. Repair all bent or damaged areas and replace any missing parts. 1 Plastic plug 1 Push nut (1/4 inch) Procedure 2 Procedure 1.
PAGE 3
4 Installing the Guards Parts needed for this procedure: 7 8 1 Left guard 1 Back guard 1 Front guard 1 Lower guard 1 Bolt (5/16 x 3/4 inch) 1 Flange nut (5/16 inch) Procedure g013159 1. Remove the existing hardware around the blower for the left guard, lower guard and back guard (Figure 5 or Figure 6). Save all existing hardware Figure 3 For model 78551, 78552, 78562, and 78566 (48-inch (122 cm) or 52-inch (132 cm)) 1. Existing hardware 5. Plastic plug 2. New blower cover 6.
PAGE 4
1 9 g016066 Figure 5 For model 78551, 78552, 78562, and 78566 (48-inch (122 cm) or 52-inch (132 cm)) 1. Existing hardware 6. Front guard Figure 6 For model 78553, 78563, and 78567 (60 inch (152 cm)) 2. Left guard 7. Lower guard 1. Existing hardware 3. Back guard, 52 inch (132cm) 8. Existing nuts 4. Flange nut (5/16 inch) 9. Back guard, 48 inch (122cm) 2. Left guard 6. Front guard 3. Back guard 7. Lower guard 4. Flange nut (5/16 inch) 5. Bolt (5/16 x 3/4 inch) 4 5.
PAGE 5
6 Installing the Support Rod Installing the Muffler Guard Parts needed for this procedure: Parts needed for this procedure: 1 1 Support rod Procedure Muffler guard Procedure 1. Slide the existing support rod out of the mower-deck curtain (Figure 7); retain the rod for future use of the machine without the bagger. 1. Remove the existing muffler guard and save the hardware. Save the existing muffler guard for use when the bagger is removed. 2.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8