Form No. 3394-391 Rev A CE Bagger Compliance Kit 48in Z Master® 2000 Series Mower Model No. 127-0339 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Note: To create a CE bagger, install this kit on the Blower and Drive Kit model 78571 and with the E-Z Vac™ Twin Soft Bagger Kit model 78569. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
. Remove the side discharge chute from the mower deck (Figure 1). 1 Note: Retain the chute and hardware for installation when operating the mower with the blower accessory removed. Preparing the Mower No Parts Required 3 Procedure 1. Park the machine on a level surface, set the parking brake, and remove the ignition key. Removing the Belt Cover and Bracket 2. Thoroughly clean mower deck. All debris must be removed to ensure the kit will fit properly. 3.
4 1 2 Removing the Blower Kit Parts (If Installed) 5 3 No Parts Required 4 Removing the Belt Cover for the Blower If the blower kit is installed on the machine, remove the belt cover installed from blower and drive kit as follows: 1. Remove the thumbscrew that secures the belt cover (Figure 4). G018856 Figure 3 1. Bolt (retained to the belt cover) 4. Flange nut (3/8 inch) 2. Belt cover 5. Carriage bolt (3/8 x 7/8 inch) 3. Cover-mounting bracket 3.
Removing the Shaft Cover and Hardware 1. Remove the 3 serrated nuts that secure the shaft cover to the blower assembly (Figure 6). Note: Do not loosen the bolts and nuts that secure the upper-bearing housing that are beneath the shaft cover. Note: Retain the serrated nuts for the shaft guard installation; refer to Installing the Shaft Guard (page 6). 1 2 3 Figure 5 1. Carriage bolt (1/4 x 3/4 inch) 4 3. Locknut 2. Belt cover bracket 5 2. Remove the belt cover bracket from the mower deck (Figure 3).
3. Secure the pulley guard and the belt cover bracket to the forward deck flange at the outboard hole with the carriage bolt (1/4 x 1 inch, CE kit) and the locknut (1/4 inch, blower kit) that you removed in step 1 of Removing the Belt Cover Bracket (page 3); refer to Figure 7. 5 Installing the Pulley Guard and Belt-cover Bracket 4.
3. Align the tensioner guard to the upper blower housing (Figure 8). 6 4. Secure the tensioner guard to the upper blower housing with 2 hex-head bolt (1/4 x 3/4 inch) and 2 locknut (1/4 inch) that you removed in step 3 of Removing the Shaft Cover and Hardware (page 4); refer to Figure 8. Installing the Upper Guards Parts needed for this procedure: 1 Shaft guard 1 Forward guard 1 Tensioner guard 7 Installing the Lower Guard Installing the Shaft Guard Parts needed for this procedure: 1.
Drilling the Mounting Holes for the Lower Guard 2. Move the idler pivot bracket toward the fixed spring post. remove the hook of the spring from the idler spring post (Figure 9). 1. Align the lower guard to the blower-chute bracket as shown in Figure 11. 3. Route the belt beneath the idler pulley (Figure 10). 4 1 5 6 7 3 1 2 2 10 10 3 7 4 5 8 9 9 11 G018859 Figure 11 6 G018367 2. Hole 2 8. Locknut (1/4 inch) 1. Drive pulley 5. Blower (housing repositioned for illustrative purposes) 2.
Installing the Lower Guard 8 Note: Install the lower guard with the blower assembly removed from the mower deck; refer to the 48in E-Z Vac™ Blower and Drive Kit Installation Instructions. Installing the Belt Cover 1. Align the lower guard to the blower-chute bracket (Figure 11). Parts needed for this procedure: 2. Align hole 2 and hole 4 of the lower guard to the rivet tails protruding through the blower-chute bracket(Figure 11). 3.
2. Insert the bolt and washer through the hole in the top of the belt cover from the blower and drive kit (Figure 12). 9 3. From the bottom of the belt cover, assemble the washer (1/4 x 1/2 inch) and retainer over the hex-head bolt threads (Figure 12). Installing the Support Rod Ensure that the bolt head and washer are positioned flush with the upper surface of the belt cover and the washer and retainer are flush with the bottom surface of the cover.
Notes: 10
Notes: 11
