Installation Instructions

ManualsBrandsToro ManualsBlades & SharpenersHigh-Lift Blade Conversion Kit for TimeMaster 2012

FormNo.3379-433RevA

High-LiftBladeandBafeKit

2012TimeMasterLawnMower

ModelNo.127-6879

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Important:Youwillneedatorquewrenchtoinstallthebladesproperly.Ifyoudonothaveatorquewrenchorare

uncomfortableperformingthisprocedure,contactanAuthorizedServiceDealer.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

PreparingtheMachine

NoPartsRequired

Procedure

1.Lockthehandleintheverticalposition(Figure1);refer

toAdjustingtheHandleHeightintheOperator’sManual.

g024066

Figure1

1.Handlelockedintheverticalposition

2.Disconnectthewirefromthesparkplug.

WARNING

Thebladesaresharp;contactingabladecould

resultinseriouspersonalinjury.

•Disconnectthewirefromthesparkplug.

•Weargloveswhenservicingtheblade.

3.Tipthemachineontoitsside,withthedipstickdown,

untiltheupperhandlerestsontheground.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3379-433*A

Summary of content (4 pages)

PAGE 1
Form No. 3379-433 Rev A High-Lift Blade and Baffle Kit 2012 TimeMaster Lawn Mower Model No. 127-6879 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Important: You will need a torque wrench to install the blades properly. If you do not have a torque wrench or are uncomfortable performing this procedure, contact an Authorized Service Dealer.
PAGE 2
3 Removing the Existing Blades Installing the Baffle No Parts Required Parts needed for this procedure: 1 Procedure 1. Use a block of wood to hold each blade steady, and turn the blade bolt counterclockwise as shown in Figure 2. Baffle Procedure 1. Remove the 4 bolts and 4 nuts in the front of the machine housing (Figure 4). Figure 4 1. Bolt (4) 3. Nut (4) 2. Baffle Figure 2 2. Install the baffle with the 4 bolts and 4 nuts that you removed in step 1 (Figure 4). 2.
PAGE 3
4. Install the other blade in the same manner as the first blade (refer to steps 1 and 2). 4 Note: The blades should be perpendicular, forming an inverted “T” as shown in Figure 6. Installing the High-lift Blades 1 Parts needed for this procedure: 2 High-lift blade Procedure G016536 1. Install the first blade so that it is horizontal, along with all mounting hardware as shown in Figure 3. Figure 6 Note: Tighten the bolt with your fingers. 1.
PAGE 4
1 1 g024068 Figure 9 g024067 1. Insert the leg of the spring here. 2 Figure 7 1. Hex-head bolts 6. Wedge the side-discharge-door assembly open with a large screwdriver so that you can install the door assembly onto the mower housing (Figure 10). 2. Side-discharge opening 2. Pry the rod out of the spring on the side-discharge door with a large, flat-head screwdriver so that the other end of the rod is beyond the opening in the end of the door hinge (Figure 8). G024031 Figure 10 7.