Installation Instructions

ManualsBrandsToro ManualsVehiclesWork Light Kit, Workman GTX/MD/MDE/MDX/HDX Cab Kit

FormNo.3436-923RevA

WorkLightKit

Workman

GTX/MD/MDE/MDX/HDXCabKit

ModelNo.130-5485

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Leftmount

Rightmount1

Bolt(M6)

Nut8

Extensionplate(GTXmachinesonly)

Rearmount1

Hex-headbolt(1/4x7/8inch)

Speednut

Tieclip3

Installthemounts.

Switch

Wireharness1

Magnettiewrap(GTXmachinesonly)

Installtheswitchandwireharness.

Work-lightassembly3Installtheworklights.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3436-923*A

Summary of content (8 pages)

PAGE 1
Form No. 3436-923 Rev A Work Light Kit Workman® GTX/MD/MDE/MDX/HDX Cab Kit Model No. 130-5485 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 © 2019—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Qty.
PAGE 2
1 2 Preparing the Machine Installing the Mounts No Parts Required Parts needed for this procedure: Procedure 1 Left mount 1 Right mount 1. Park the machine on a level surface. 8 Bolt (M6) 2. Engage the parking brake. 8 Nut 3. Shut off the engine and remove the key. 2 Extension plate (GTX machines only) 4. Disconnect the negative battery cable from the battery post.
PAGE 3
Installing the Front Mounts Installing the Rear Mount Workman GTX Machines Only For All Machines 1. 1. Install a tie clip to the right mount (Figure 3). Drill a hole (3/8 inch) in the rear of the roof (Figure 4). g035792 Figure 3 1. Tie clip 4. Right mount 2. Nut 3. Extension plate 5. Bolt g308107 Figure 4 1. Drill a hole (3/8 inch) in the rear of the roof. 2. 3. Install the right mount to 1 extension plate using 2 bolts and 2 nuts (Figure 3). 2.
PAGE 4
Routing the Wire Harness 3 Workman MD/MDE/MDX/HDX Machines Only 1. Install the wire harness as shown in Figure 7. Installing the Switch and Wire Harness Parts needed for this procedure: 1 Switch 1 Wire harness 7 Magnet tie wrap (GTX machines only) Installing the Switch From the underside of the cab control panel, push the plug out of the hole shown in Figure 6 and install the work-light switch into this hole. g027575 Figure 7 View from above 2.
PAGE 5
Routing the Wire Harness 4 GTX Machines Only 1. Install the wire harness as shown in Figure 9. Installing the Work Lights Note: Slit the foam at the locations shown in Figure 9 to route the harness. Parts needed for this procedure: 3 Work-light assembly Procedure 1. Install the top of the cab that was removed in 1 Preparing the Machine (page 2) onto the machine. 2. Remove the nut and bolt from each work-light assembly and secure them to the brackets as shown in Figure 11.
PAGE 6
Operation Controls Work-Light Switch Press the work-light switch to the ON position to activate the work lights.
PAGE 7
Notes:
PAGE 8