Installation Instructions

ManualsBrandsToro ManualsSprayersFinishing Kit, Foam Marker for Multi Pro 1200 Series Turf Sprayer

FormNo.3392-306RevA

FinishingKit

FoamMarkerforMultiPro

1200SeriesTurfSprayer

ModelNo.130-8281

InstallationInstructions

Note:TheFoamMarkerKitisrequiredfortheinstallationofthisproduct.ContactyourAuthorizedToroDealerfor

moreinformation.

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

UseofthisproductmaycauseexposuretochemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orotherreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Foammarkeradapterharness1

Cabletie

Installthefoammarkeradapter

harness—2009andbeforemodels.

Foammarker(soldseparately)

Hex-headscrew(1/4x0.62inch)

Locknut(1/4inch)

Attachthefoammarker(sold

separately).

Foam-markerbracket1

Carriagescrew(3/8x1inch)

Flangenut(3/8inch)

Installthenishing-kitbracket.

Switch

Fuse(15amp)

Installtheswitchesandthefuse.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3392-306*A

Summary of content (8 pages)

PAGE 1
Form No. 3392-306 Rev A Finishing Kit Foam Marker for Multi Pro® 1200 Series Turf Sprayer Model No. 130-8281 Installation Instructions Note: The Foam Marker Kit is required for the installation of this product. Contact your Authorized Toro Dealer for more information. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
PAGE 2
1 Installing the Foam Marker Adapter Harness—2009 and Before Models Parts needed for this procedure: 1 Foam marker adapter harness 4 Cable tie Verifying the Machine Wiring Harness 1. Look for the wiring harness of the machine at the right side, approximately mid way along the tank, between the tank and the chassis. 2. Look for a branch of the machine wiring harness with a 4-socket electrical connector labeled Foam Marker (Figure 1).
PAGE 3
Routing and Connecting the Foam Marker Adapter Harness Figure 2 1. Foam-marker connector (if present on the machine harness) 5. 4-socket electrical connector (foam marker adapter harness) 2. Foam-marker tank assembly 6. 2-socket connector—labeled Left and Right (foam marker adapter harness) 3. 2-pin connector—black power plug (main wiring harness—2009 and before models)—labeled Foam Marker 7. 2-pin connectors—labeled Left and Right solenoid (main wiring harness—2009 and before models) 4.
PAGE 4
located so that you can connect the harness once the foam-marker assembly is installed. 3 9. Tie back any loose wiring along the harness to avoid snagging it during operation. Installing the Finishing-Kit Bracket 2 Parts needed for this procedure: Attaching the Foam Marker (Sold separately) 1 Foam-marker bracket 5 Carriage screw (3/8 x 1 inch) 5 Flange nut (3/8 inch) Parts needed for this procedure: 1 Foam marker (sold separately) 4 Hex-head screw (1/4 x 0.
PAGE 5
3. Insert the 15-amp fuse into the top socket of the fuse block(Figure 7). 4 Note: Ensure that the fuse is fully seated in the socket. Installing the Switches and the Fuse Parts needed for this procedure: 2 Switch 1 Fuse (15 amp) Procedure 1. Remove the 2 plugs from the control panel (Figure 5). Figure 7 1. 15-amp fuse Figure 5 1. Plugs 2. Connect the switches to the electrical connectors in the control panel and then insert the switches into the panel (Figure 6). Figure 6 1. Switches 5 2.
PAGE 6
Operation 1 2 Using the Controls Right foam on/off switch—Use the right foam on/off switch to activate the compressor, generating a flow of foam to the right boom. Left foam on/off switch—Use the left foam on/off switch to activate the compressor, generating a flow of foam to the left boom. Indicator markings—Use the indicator markings located on the side of the foam-marker tank to identify the level of foam solution in the tank. g023901 Figure 8 1.
PAGE 7
Notes: 7
PAGE 8