Installation Instructions

ManualsBrandsToro ManualsSprayersFinishing Kit, Foam Marker for Workman Utility Vehicle 200 Gallon Spray System

FormNo.3384-322RevA

FinishingKit

FoamMarkerforWorkman

UtilityVehicle200GallonSpray

System

ModelNo.130-8282

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Note:TheFoamMarkerKitisrequiredfortheinstallation

ofthisproduct.ContactyourAuthorizedToroDealerfor

moreinformation.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Foam-markermountbracket1

Flanged-headbolt(3/8x1-1/4inch)

Flangedlocknut(3/8inch)

Installthesupportbracketforthemarker

tank.

Foam-markerassembly(sold

separately)

Flanged-headbolt(1/4x5/8inch)

Flangedlocknut(1/4inch)

Installthefoam-markerassembly

(foam-markerassemblysold

separately).

Switch

2Installthecontrolswitches.

Fuse(15amp)

Installthefuse.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3384-322*A

Summary of content (8 pages)

PAGE 1
Form No. 3384-322 Rev A Finishing Kit Foam Marker for Workman® Utility Vehicle 200 Gallon Spray System Model No. 130-8282 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Note: The Foam Marker Kit is required for the installation of this product. Contact your Authorized Toro Dealer for more information.
PAGE 2
1 Installing the Support Bracket for the Marker Tank Parts needed for this procedure: 1 Foam-marker mount bracket 4 Flanged-head bolt (3/8 x 1-1/4 inch) 4 Flanged locknut (3/8 inch) Figure 2 Procedure 1. Remove the 2 bolts and 2 nuts that secure the lifting handle at the forward end of the left-tank rail and remove the lifting handle (Figure 1). 1. Lifting handle 4. Hole (tank-frame rail) 2. Flanged-head bolt (3/8 x 1-1/4 inch) 5. Engine-access door 3. Foam-marker mount bracket 6.
PAGE 3
2 3 Installing the Foam-marker Tank Installing the Control Switches Parts needed for this procedure: Parts needed for this procedure: 1 Foam-marker assembly (sold separately) 4 Flanged-head bolt (1/4 x 5/8 inch) 4 Flanged locknut (1/4 inch) 2 Switch Disconnecting the Battery 1. Squeeze the battery cover to release the tabs from battery base (Figure 4). Procedure 1. Align the holes under the support frame for the foam-marker assembly with the holes in the foam-marker mount bracket (Figure 3).
PAGE 4
1 2 4 3 G022071 Figure 5 1. Terminal cover 3. Battery post 2. Positive terminal 4. Battery Installing the Control Switches 1. Remove the 2 cover plugs located at the top right corner of the cover for the sprayer-control panel (Figure 6). Figure 6 1. Sprayer-control panel 4. Electrical connector 2. Panel opening (sprayer-control panel) 5. Control switch 3. Plug 6. Body notch (control switch) 2. Gently pull the 2 electrical connectors through the panel openings (Figure 6).
PAGE 5
3. Align the switches to the connectors with the notch in the body of the switch down (Figure 6). Operation 4. Connect the switches to the electrical connectors (Figure 6). Using the Controls 5. Snap the switched into the panel opening in the sprayer-control panel (Figure 6). Right foam on/off switch—This switch activates the compressor, generating a flow of foam to the right boom. Left foam on/off switch—This switch activates the compressor, generating a flow of foam to the left boom.
PAGE 6
Note: If you leave the foam in the line for more than 2 hours, it may become watery. Before operating after a break of 2 or more hours, run the machine for 1 to 2 minutes to remove the excess water. drops; decreasing the flow results in smaller, less frequent foam drops (Figure 10). Note: A watery marker consistency may be helpful on windy days.
PAGE 7
Notes: 7
PAGE 8