Installation Instructions

ManualsBrandsToro ManualsSprayersFoam Marker Finishing Kit, 2015 and After Multi Pro 5800 Turf Sprayer

FormNo.3384-337RevB

FoamMarkerFinishingKit

2015andAfterMultiPro

5800TurfSprayer

ModelNo.130-8292

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

UseofthisproductmaycauseexposuretochemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orotherreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparetoinstallthekit.

Foammarker(soldseparately)

Supportbracket

Bolt(1/4x7/8inch)

Flangedlocknut(1/4inch)

Washer(1/4inch)

Assemblethefoammarker.

Flangedlocknut(5/16inch)

Carriagebolt(5/16x1-1/4inch)

Installthenishingkitbracket.

Wiringharness1

Cabletie

Routethewiringharness.

Relay1

Flange-headbolt(#10-24x1/2inch)

Fuse(15amp)

Connectthewiring.

Flange-headbolts(6x12mm)

Mountingbracket(foam-controlswitch)

3-positionpaddleswitch(foam-control

switch)

2-positionrockerswitch(compressor

On/Offswitch)

Installtheswitches.

Nopartsrequired

–

Finishtheinstallationofthekit.

Note:TheFoamMarkerKitisrequiredtoinstallthisproduct.ContactyourAuthorizedToroDealerformoreinformation.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3384-337*B

Summary of content (16 pages)

PAGE 1
Form No. 3384-337 Rev B Foam Marker Finishing Kit 2015 and After Multi Pro® 5800 Turf Sprayer Model No. 130-8292 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
PAGE 2
1 1 Preparing to Install the Kit No Parts Required Procedure 3 2 G014029 Figure 1 WARNING 1. Battery cover Incorrect battery cable routing could damage the sprayer and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. 3. Buckle 2. Strap • Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable. • Always reconnect the positive (red) battery cable before reconnecting the negative (black) cable.
PAGE 3
2 3 Assembling the Foam Marker Installing the Foam Marker and Support Bracket Parts needed for this procedure: Parts needed for this procedure: 1 Foam marker (sold separately) 1 Support bracket 4 Flanged locknut (5/16 inch) 4 Bolt (1/4 x 7/8 inch) 4 Carriage bolt (5/16 x 1-1/4 inch) 4 Flanged locknut (1/4 inch) 4 Washer (1/4 inch) Procedure 1.
PAGE 4
5. Align the holes in the rear leg of the support bracket with the holes in the splash guard, fender bracket, and fender (Figure 6). 6. Secure the support bracket to the splash guard, fender bracket, and fender with 2 carriage bolts (5/16 x 1-1/4 inch) and 2 flanged locknuts (5/16 inch) as shown in Figure 6. 4 Routing the Wiring Harness Parts needed for this procedure: Figure 5 1. Splash guard 4. Right, rear fender 2. Carriage bolt 5.
PAGE 5
Figure 8 1. 236 cm (93 inch)—compressor branch Figure 10 3. Cable ties 2. Sprayer-tank straps 2. Route the 4-socket connector of the harness to the 4-pin connector of the compressor and connect the 2 connectors. Note: The compressor is located above the foam-marker tank. 1. Route the wiring harness for the finishing kit forward between the ROPS bar and the lower corner of the sprayer tank, along the wiring harness of the machine, and below the air cleaner for the engine (Figure 9 and Figure 10). 2.
PAGE 6
Figure 11 1. Cable ties 7. Blade connector (wiring harness for the finishing kit) 2. 197 cm (77-1/2 8. Front of the machine inch)—engine-compartment branch 3. Base of the center console 9. 240 cm (94-1/2 inch)—dash-panel branch (routed down) 4. Wiring harness for the machine 5. Ring terminal (wiring harness for the finishing kit) Figure 12 10. Radiator 11. Air filter 6. 5-socket connect (wiring harness for the finishing kit) 1. Cable tie 5. 240 cm (94-1/2 inch)—dash-panel branch 2. R-clamps 3.
PAGE 7
2. Route the 240 cm (94-1/2 inch)—dash-panel branch of the wiring harness to the R-clamp at the ground-speed-control coil (Figure 12 and Figure 13). 3. Route the 240 cm (94-1/2 inch)—dash-panel branch of the wiring harness through the grommet at the opening in the forward bulkhead and inboard of the cable and hose hook (Figure 14). Figure 15 Figure 14 1. 8-socket connector (compressor switch) 4. 8-socket connector (wiring harness for the finishing kit) 2. Cable and hose hook 5.
PAGE 8
Installing the Relay 5 1. At the 197 cm (77-1/2 inch)—engine-compartment branch of the wiring harness, align the relay with the 5-socket connect of the wiring harness for the finishing kit (Figure 18). Connecting the Wiring Parts needed for this procedure: 1 Relay 1 Flange-head bolt (#10-24 x 1/2 inch) 1 Fuse (15 amp) Connecting the Compressor Wiring 1.
PAGE 9
Connecting the Ground Wire Connectors 1. Remove a screw from the ground-terminal block (Figure 19). Figure 20 Figure 19 1. Ground-terminal block 3. Ring terminal (ground) 1. Fuse Block (machine) 3. Blade connector (wiring harness for the finishing kit) 2. 2-pin connector (auxiliary-feed wires) 4. Socket connector (fuse block for the machine) 2. Screw 2.
PAGE 10
Connecting the Load Wire Connectors (Optional Auxiliary-Fuse Block) 1. Connect the blade connector of the wiring harness for the finishing kit to the socket connector of the auxiliary-fuse block (Figure 21). Note: Press the connectors together until the latch snaps securely. Figure 22 1. Auxiliary fuse block 4. 2-socket connector (feed wires of the auxiliary-fuse block) 2. Mounting flange (fuse block for the machine) 5. 2-pin connector (auxiliary-feed wires, fuse block for the machine) 3.
PAGE 11
Installing the Fuse 6 • For a machine with the bladed-attachment connector at the fuse block for the machine, install the 15-amp fuse into the fuse block (Figure 23).
PAGE 12
2. Align the 8-socket connector through the opening in the dash panel and connect the connector (Figure 28) to the pins at the back of the 2-position rocker switch (COMPRESSOR ON/OFF switch). Figure 26 1. 3-position paddle switch (FOAM-CONTROL switch) 3. Opening (mounting bracket for the FOAM-CONTROL switch) 2. 8-socket connector Figure 28 1. 8-socket connector 4. Assemble the switch into the bracket and press in the switch until it snaps securely into the opening (Figure 26).
PAGE 13
Operation Using the Controls • COMPRESSOR ON/OFF switch—Use this switch to run the compressor for the foam marker system. • FOAM -CONTROL switch—Use this switch to control which boom from which foam flows. – Move the paddle down to apply foam from the left-boom section. – Move the paddle to the center position apply foam from the left- and right-boom sections. – Move the paddle up to apply foam from the right-boom section.
PAGE 14
Notes: 14
PAGE 15
Notes: 15
PAGE 16